36
English
WARNINGS
General
•
Do not use any sharp tools to open the
packaging.
•
We strongly advise against using power tools.
•
Tripping hazard, mind your step.
•
Do not put out cigarettes on the shade.
•
Not grafitti proof.
•
Do not leave children unattended whilst playing
underneath the shade.
•
Colors can differ over years and from batch to batch.
Product
•
Do not drag the shade, but carry it with minimum
2 people.
•
Anchoring the product has to be done by
qualified people.
•
For anchoring: use suitable bolts or screws from
a specialized store depending on the material
your terrace is made of.
•
In case of strong winds or if it is not being used,
close the shade and tilt the latches downwards.
Put the protective cover over the shade to
prevent it from blowing open or getting dirty.
•
For ventilation purposes, the cover is not 100%
water proof.
•
Store the parasol when not in use for a long
time as follows: completely dry and in a dry
environment.
•
Do not leave the parasol closed for a long time
when the parasol fabric is still damp or wet.
•
Do not leave the shade unattended when
opened.
•
Tests in a wind tunnel have shown that the
parasol withstands wind speeds up to 5 on the
Beaufort scale. Still, it is best to close it sooner.
•
Fix the closed Sensu with the supplied strap.
Powder coating
•
White powder coating requires more
maintenance.
•
Do not use abrasive scouring powders or
scourers as they will scratch the surface.
•
Color can fade to some extent when exposed to UV.
•
Flame retarding - NEN-EN13501-1 A2-sl -
Satisfying the same criteria as Class B for the
SBI-test according to EN13823. In addition,
under conditions of a fully developed fire these
products will nog significantly contribute to the
fire load and fire growth.
•
Dark colors can get very hot in sunny weather.
Acrylic fabric
•
White fabric requires more maintenance.
•
Shake or brush off loose dirt immediately.
•
Do not use any aggressive detergents as they will
remove the protective coating of the fabric.
•
We strongly advise you not to use a high-
pressure hose for cleaning.
•
UV colour fasteness: 7/8 (ISO 105-B02).
ASSEMBLY INSTRUCTIONS
Duo square with base - p8
1. Fix the feet to the bottom of the base using four
M6x12 bolts for each.
2. Put two large and seven small concrete tiles per
corner on the base.
3. Remove the four outer bolts as shown in the
drawing. Attention: do not throw away the bolts,
you will need these again in step 4.
4. Now fix the parasol support with the four bolts
from step 3 onto the base.
5. Position the large cover plate on top of the base.
6. Now position the small cover plate and rubber
spacer on top as shown in the drawing.
7. Slide the two handles into the pole from below
and tighten them at +/- 1 meter height as shown
in the drawing.
8. Remove the cover plate on top of the pole.
Attention: do not throw away the cover plate and
bolts!
9. Slide the parasol pole on top of the parasol
support.
10. Now remove the stainless steel hinge axle and
bolts from the parasol arm as shown in the
drawing.
11. Slide the top of the support rib into the pole
from above. Attention: make sure the hole of
the bracket is facing upwards as shown in the
drawing.
12. Position the parasol arm onto the handle.
13. Fix the parasol arm onto the handle with the
hinge axle and bolt.
14. Now fix the top of the support rib to the pole with
one M8x20 bolts & one M8 nut.
15. Repeat steps 10 - 14 for the other parasol arm.
16. Finally, mount the cover plate back on top of the
pole with the four bolts.
Warnings – Assembly text instructions – Maintenance
Summary of Contents for Sensu Duo square
