Extreme Networks Summit WM3700 Installation Manual Download Page 12

Page: 12 / 45

LED Codes

Summit WM3700 Wireless LAN Controller Installation Guide

NOTE

During controller start up, the Temperature status LED will be lit Solid Amber. This is normal
behavior and does not indicate an error. At the completion of start up the Temperature Status LED
will switch to Solid Green.

Controller Status (Primary System)

Controller Status (Redundant System)

System Status 1 LED

System Status 2 LED

Event

Off

Power off

Green Solid

Off

No Redundancy Feature Enabled

Green Solid

Redundancy Feature Enabled

Actively Adopting Access Points

Green Solid

Amber Blinking

No License to adopt Access Points or No

Country Code configured on the controller.

System Status 1 LED

System Status 2 LED

Event

Off

Power off

Green Solid

Off

No Redundancy Feature Enabled

Green Blinking

Green Solid

Redundant System failed over and

adopting ports

Green Blinking

Alternating Green

Blinking & Amber

Blinking

Redundant System not failed over.

Green Solid

Amber Blinking

No License to adopt Access Points or No

Country Code configured on the controller.

WM3700InstallGuide.book Page 12 Wednesday, December 2, 2009 3:15 PM

Summary of Contents for Summit WM3700














































Search results

Summary of Contents for Summit WM3700

Reviews:

Brands by name

Popular brands

Extreme Networks Summit WM3700, Installation Manual

Search results

Summary of Contents for Summit WM3700

Reviews:

Brands by name

Popular brands