manualshive.com logo in svg

Extreme Networks ExtremeWireless AP410e, Installation Manual, Page: 37 / 45

Share
Download
Extreme Networks ExtremeWireless AP410e Installation Manual Download Page 37

Warning
IC Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 39
cm between the radiator and your body.

Warning
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum
de 39 cm de distance entre la source de rayonnement et votre corps.

Detachable Antenna Usage

ISED (IC) warning statement

This radio transmitter [IC: 4141B-AP410] has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible
gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain
indicated for any type listed are strictly prohibited for use with this device.

Le présent émetteur radio [IC: 4141B-AP410] a été approuvé par Innovation, Sciences et Développement
économique Canada pour fonctionner avec les types d'antenne énumérés ci

‑

dessous et ayant un gain

admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de
l'émetteur.

Group Brand

Model number

Antenna type

Antenna gain (dBi)

2.4

GHz

5 GHz BLE or

thread

1

Extreme

ML-2452-APA2-01

Omni

3.04

4.96

-

2

Extreme

ML-2452-APA2-02

Omni

3.04

4.96

-

3

Extreme

ML-2452-HPA5-036

Omni

3.9

5.7

-

4

Extreme

ML-2452-HPAG4A6-01

Omni

4

7.3

-

5

Extreme

ML-2452-PNA5-01R

Panel

4.5

5

-

6

Extreme

ML-2452-PTA4M4-036

Omni

5

6.6

-

7

Extreme

ML-2452-HPAG5A8-01

Omni

5

8

-

8

Extreme

WS-AO-DQ04360N

Omni

5.5

6

-

9

Extreme

AI-DQ04360S

Omni

5.5

6

-

10

Extreme

ML-2452-SEC6M4-036 /

WS-AI-DQ05120

Panel

6.92

7.23

-

11

Extreme

WS-AI-DE07025

Panel

7.5

6.5

-

12

Extreme

ML-2452-PNA7-01R

Panel 1

7.8

10.7

7.8

Regulatory Information

Detachable Antenna Usage

ExtremeWireless™ Access Points AP410i/e

37

Summary of Contents for ExtremeWireless AP410e














































Reviews:

No comments