manualshive.com logo in svg

Extech Instruments MG500, User Manual, Page: 8 / 15

Share
Download
Extech Instruments MG500 User Manual Download Page 8

MG500-en-GB_v1.3   3/17

 

8 

The Enersave

TM

 Mode 

Enersave

TM

  mode conserves battery life by performing a relatively short test. The  Enersave

TM

 

mode is the default test mode. To bypass this mode and run a longer test (10 minutes) press and 

hold the TEST button for more than 3 seconds when starting a test.  

 

DAR and PI Tests 

(DAR: Dielectric Absorption Ratio)

 

and (PI: Polarization Index)

 

 

Warning:

 The circuit under test must

 

be completely 

de-energized

 and isolated before

 

making

 

test connections. 

 

1.

 

After turning the unit on, make sure that the 

Replace Battery

 message is not displayed.  If 

the 

Replace Battery

 message is displayed replace the batteries before proceeding. 

2.

 

The test voltage defaults to 2500V on power up. Select the desired  test voltage using the 

Voltage Adjust buttons (±500V) that  step through the available test voltages in 500V 

increments or by pressing one of the preset test voltage buttons (10kV, 5kV, 2.5kV, 1Kv). 

3.

 

The display shows the 

Connect Leads

 prompt along with the selected test voltage value.   

Connect the Green test lead to the Green test socket on the meter and then to the Ground 

side of the insulator under test.   

Connect the Red lead to the Red test socket on the meter and the Blue guard cable to the 

blue socket on the meter. Connect the service end of the Red cable to other side of the 

insulator under test.   

If a Leakage Guard lead is required to collect surface leakage, connect the separate Blue test 

lead into the Blue guard lead from the Red test lead which is plugged into the Blue test 

socket  on the meter and then clip the service end of the cable to the surface of the 

insulator under test. 

4.

 

Press and hold the 

Test Start/Stop

 button for more than 3 seconds to the initiate DAR/PI 

testing mode. 

5.

 

After 1 minute, the elapsed test timer appears on the upper line (right hand side) of the 

display. The resistance reading is shown on the upper left hand side of the display. The lower 

line shows the test voltage and the DAR value. 

6.

 

After 10 minutes, the test completes. The display will show the results: 

R

 = (resistance or OVER R for over range) 

T

 = Hold, T = 10:00, V = (test voltage) 

PI

 = (PI value) 

DAR

 = (DAR value) 

7.

 

To take another test, press the 

TEST START/STOP

 button, the 

Connect Leads

 prompt should 

appear on the display; the instrument is now ready to run a new test. 

 

Shop for Extech products at:

1.800.561.8187

ShopExtech

.ca

Summary of Contents for MG500
















Reviews:

No comments