Extech Instruments ExStik EC500 User Manual Download Page 12

Page: 12 / 14

EC500-en-US_v2.9 7/20

Cleaning Recommendations

When cleaning the probe, take care not to scratch or damage the sensing surface or the platinized
electrode surfaces.

Contaminant

Cleaning Solution

Instructions

Water soluble substances

Deionized water

Soak or scrub with a soft
brush. Recondition in 4 or 7
buffer for 1 hour.

Grease & Oil

Warm water and household
detergent

Soak or scrub with a soft
brush, maximum of 10
minutes. Rinse thoroughly
with DI water, recondition in 4
or 7 buffer for 1 hour.

Heavy grease & Oil

Alcohol

Maximum of 5 minute soak,
scrub with a soft brush. Rinse
thoroughly with DI water,
recondition in 4 or 7 buffer for
1 hour.

Lime and hydroxide coatings

10% acetic acid

Soak until coating dissolved,
maximum of 5 minutes. Rinse
thoroughly with DI water,
recondition in 4 or 7 buffer for
1 hour.

Please Note:

Since the EC500 does not have a refillable pH reference electrolyte chamber, it is

important not to soak the electrode in the above solutions for more than the recommended times. To
do so may cause a reference potential shift, which will cause degradation in performance or failure.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for ExStik EC500















Search results

Summary of Contents for ExStik EC500

Reviews:

Related manuals for ExStik EC500

Brands by name

Popular brands

Extech Instruments ExStik EC500, User Manual

Search results

Summary of Contents for ExStik EC500

Reviews:

Related manuals for ExStik EC500

Brands by name

Popular brands