Extech Instruments CO250 User Manual Download Page 2

Page: 2 / 9

CO250-EU V1.2 6/09

Meter Description

METER

Temperature and Humidity sensor

sensor (rear)

LCD display

AC Adaptor connector

RS232 port

Keypad

Battery compartment (rear)

LCD DISPLAY

CO2 concentration in ppm

Relative Humidity in %

Air Temperature, Dew Point or
Wet Bulb Temperature

SYMBOLS

TWA

Time weighted average( 8 hours)

STEL

Short-term exposure limit (15 minutes weighted average)

HOLD

Freezes current reading on display

MIN/MAX

Minimum/Maximun readings
Low battery indicator

Dew point temperature

AIR

Air temperature

WBT

Wet bulb temperature

Unit of relative humidity

C or F

Celsius/Fahrenheit

KEYPAD

Turns the meter on and off.
Enters setup mode.
Sets as non-sleep mode with

Exits setup page/mode.
Enters CO

calibration with

Enters RH calibration with

Freezes the current reading on display.
Cancels data hold function.

Activates or cancels the backlight.
Selects unit or increases value in setup.

Selects AIR, DP, WBT temps display.
Selects unit or decreases value in setup.

Activates MIN,MAX,STEL,TWA function.
Saves and finishes settings.

Summary of Contents for CO250










Search results

Summary of Contents for CO250

Reviews:

Related manuals for CO250

Brands by name

Popular brands

Extech Instruments CO250, User Manual

Search results

Summary of Contents for CO250

Reviews:

Related manuals for CO250

Brands by name

Popular brands