Extech Instruments 381295 User Manual Download Page 31

Page: 31 / 31

381295 381295-220 V1.3 5/06

Appendices

Troubleshooting guide

If you experience a problem with the meter, try the corrective actions below before
concluding that the instrument needs repair.

1. Make sure you are using a fresh NI-MH battery pack or fully charged rechargeable

battery pack. If you are using the AC/DC power adapter, make sure the adapter is
plugged into an appropriate live power source.

2. If the buttons do not respond or the contrast is set such that the display is unreadable,

remove the power source while the instrument is on. Wait 15 minutes and then
restore power and retry.

3. If you still experience difficulty, check your connections and reread this instruction

manual.

4. If the meter’s display is frozen when trying to control the trigger level:

•

In normal (NOR) mode, the trigger level must be the same level as the waveform.

The Meter does not trigger if the trigger level is set above or below the waveform
level.

•

In Auto (AT) mode, the trigger level does not have to be adjusted.

•

In rare cases, the instrument may require servicing. There are no internal user-

serviceable parts.

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

Summary of Contents for 381295
































Search results

Summary of Contents for 381295

Reviews:

Related manuals for 381295

Brands by name

Popular brands

Extech Instruments 381295, User Manual

Search results

Summary of Contents for 381295

Reviews:

Related manuals for 381295

Brands by name

Popular brands