manualshive.com logo in svg

Expleco Oppressor GLC, Instruction Manual

Share
Download
Expleco Oppressor GLC Instruction Manual Download Page 7

BOTTLE CRUSHER 

Model : Oppressor GLS 

Standard Operating Proceedure

IMPORTANT! 

PRIOR TO OPERATION ALL USERS MUST READ THE ENTIRE 

INSTRUCTION MANUAL 

1. This  machine  is  designed  to  crush  glass  bottles  ONLY.  Do  not  use  the

Oppressor GLS for any other use.

2. The machine is designed for interior use. Do not use the machine in wet

conditions.

3. Do not use the machine near flammable liquids or gases.
4. The  power  supply  cable  should  be  checked  and  certified  at  6  monthly

intervals by a registered electrician.

5. The power supply must be capable of delivering 230-240v @ 10 amps.
6.

Extension  cords  must  not  be  used,  other  than  those  supplied  with  the

machine. If motor won’t start overload protector may need resetting. (refer
to instruction manual)

7. Protective Goggles and earmuffs are recommended to be worn.
8. If handling broken bottles protective gloves must be worn.
9. Before starting the machine check the bucket level.
10. Never place bottles in the machine unless the machine is running and the

red LED light is on.

11. Bottles must be inserted into the machine neck down.
12. Caps  and  all  liquid  must  be  removed  from  bottles  prior  to  inserting  into

machine. Bottles can be fed immediately one after the other.

13. In the rare occurrence of a bottle jamming refer to the Instruction Manual.

If  machine  still  runs  but  bottles  jammed  in  chute  ,  then  use  T  handle  to
clear by ramming on bottle jam. If machine is stalled then you will need to
remove 8mm cap screw on rear of chute and unplug the power supply on
machine  housing.  –  remove  blocked  glass  carefully  with  protective
gloves.  The  overload  may  need  re-setting.  Only  trained  and  authorised
persons  should  open  and  service  the  machine.  If  in  doubt  immediately
contact the machine supplier.

14. 

Once bin is full turn machine off. Pull jack handle towards you to lift
housing/lid 25mm above bucket. Remove bucket to empty. Replace bin by
locating bin firmly green tray pad. Push jack handle back, ensuring that
lid flange does not catch on top of bin. Jack handle must be pushed back
until nearly vertical and then released. This will ensure that the bin

 is

properly sealed. To ensure seal only use the Expleco 20 Litre
Bucket !!

IF IN DOUBT REFER TO INSTRUCTION MANUAL 

OR CONTACT EQUIPMENT SUPPLIER 

Summary of Contents for Oppressor GLC











Reviews:

No comments

Brands by name

Popular brands

Load more brands