manualshive.com logo in svg

Expert EX-9543, User Manual, Page: 22 / 33

Share
Download
Expert EX-9543 User Manual Download Page 22

EX-9543 

  

Enhanced 10/100Base-TX to 100Base-FX Converter 

- 18 - 

2.  Check the power LED on the rear of the Converter 
3.  when the device is powered on to verify that 

power is applied. If not, check that the power 
cable is correctly and securely plugged in. 

4.  

Connecting Fiber Cable 

When connecting fiber cable to a 100BASE-FX port 
on the Converter, be sure the correct type - ST or SC 
or WDM - connector is used. Follow the steps below 
to properly connect fiber cable: 
1.  Remove and keep the ST/SC/WDM port's rubber 

cover. When not connected to a fiber cable, the 
rubber cover should be replaced to protect the 
optics. 

2.   Check that the fiber terminators are clean. You 

can clean the cable plugs by wiping them gently 
with a clean tissue or cotton ball moistened with a 
little ethanol. Dirty fiber terminators on fiber optic 
cables will impair the quality of the   light 
transmitted through the cable and lead to 
degraded   performance on the port. 

3.    Connect one end of the cable to the ST/SC/WDM 

Summary of Contents for EX-9543


































Reviews:

No comments