background image

1/2" AIR IMPACT WRENCH

TABLE OF CONTENTS

GENERAL SAFETY RULES.........................................................................................2

AIR SUPPLY..................................................................................................................4

PRODUCT DESCIPTION..............................................................................................5

TECHNICAL SPECIFICATIONS...................................................................................5

ASSEMBLY...................................................................................................................6

OPERATION.................................................................................................................8

TROUBLSHOOTING....................................................................................................9

CARE AND MAINTENACE..........................................................................................9

EXPLODED DIAGRAMS AND PARTS LISTS...........................................................10

WARRANTY................................................................................................................11

Summary of Contents for EX1603KIT













Reviews: