background image

3

EXCURSION 

It is recommend that you have your new EXCURSION SX Series Automo ve 
Speakers professionally installed by your authorizied EXCURSION dealer. This 
will ensure use of proper installa on techniques and materials and save much 

me and efforts. If you choose to perform your own installa on, the following 

instruc on will give you direc on toward making your purchase complete. Read 
the following informa on and precau ons carefully. Failure to follow the stated 
precau ons may result in personal injury or damage the audio system or vehicle.

A.) Always make sure the speaker will easily fit into the intended moun ng loca on
and that there is adequate cavity depth to accept the magnet structure. 

B.) Check for adequate clearance between speaker and window, window crank,
power window mechanism, seat, glove box, rear deck torsion bars and other 
items which may interfere with the speaker`s moun ng. This is especially 
important if any hole cu ng is required. Complete speaker, moun ng size and 
depth requirements can be found on page 9 of these instruc ons. A good way to 
confirm speaker place meet on a door or body panel is to place the speaker`s 
die cast moun ng ring onto the surface. Check for a flat moun ng surface, 
free from all obstruc on.

C.) The method of installa on choosen and level of execu on will effect the 
overall performance of the EXCURSION Speakers. Thread each installa on 
step with a high degree of a en on.

D.) Do not mount the speaker where water may splash the woofer cone. 
A plas c cup or some heavy gauge plas c shee ng may be needed in some 
loca ons that are exposed to moisture from behind the body panel.

E.) Care must be taken to prevent low frequency cancela on caused by air 
leakage between the front and rear of the speaker (such as when mounted 
on a curved or uneven surface, or when mounted in an oversized hole)

F.) Moun ng panel reinformcement may be necessary in some cases in order 
to prevent surface flex. This can be achieved by moun ng the speaker on a 
metal or wooden sub-baffle behind the body or door panel. 
Consult an installa on specialst for further direc on.

Pre-Installa on Instruc ons:

EXCURSION 

Pre-Installa on Instruc ons:

Summary of Contents for SHX SERIES













Reviews: