E X C E L D R Y E R , I N C 1 . 4 1 3 . 5 2 5 . 4 5 3 1 1 . 8 0 0 . 2 5 5 . 9 2 3 5 ( U S / C N ) E X C E L D R Y E R . C O M
A D M I N @ E X C E L D R Y E R . C O M 3 5 7 C H E S T N U T S T R E E T, E A S T L O N G M E A D O W, M A 0 1 0 2 8
2 / 2 0 2 1
2
R E A D A N D S AV E T H E S E I N S T R U C T I O N S
1. Disconnect the power source previously brought to the hand
dryer location (see pre-installation wiring above).
2. Use the Tamper-Proof Wrench supplied and remove the
Tamper-Proof Bolt on bottom of cover lifting upwards to
remove cover from base plate.
3. If electrical wiring entry is to be made from the rear, remove
the appropriate pre-formed knockout on the base plate.
If entry is to be made from the side, knock out the preformed
area on the right side of cover for your supply connection
using knockout gasket provided. A rigid conduit must be
used.
For models with metal covers,
if the side entry for
conduit is required, this must be specified in advance and
the side entry can be pre-cut and proper grommet applied by
the manufacturer.
4. Select the appropriate mounting height for dryer (Table 1)
and fastener, as recommended (Table 2). There should
be no obstruction between the hand dryer and the floor.
If mounting over a countertop, distance from counter to dryer
must be 15” (381 mm) minimum.
CAUTION:
Do not use Base Plate as a guide when drilling.
Make sure no pipe work (gas, water, air) or any electrical cables
or wires are located directly behind the area to be drilled.
5. Attach Base Plate at the four corners to smooth wall.
Use one of 2 knockouts provided for service entry on back of
Base Plate. If using surface wiring use knock out in right side
of cover. Use Knockout Gasket supplied around conduit for
water seal. See Mounting Details.
6. Identify the voltage of your dryer from the rating sticker of
the unit. Then connect to a circuit per your local wiring and
building regulations.
7. Secure electrical wiring to terminals as indicated by the
schematic affixed to blower housing. An identified ground
connection point is supplied on the Base Plate for your
equipment ground wire. Dryers should be installed per local
code requirements.
8. In multiple installations, make sure the serial number marked
on the inside matches the cover number. Then carefully
replace Cover by inserting top of cover over bracket and
tilting downward. Use Tamper-Proof Bolt previously
removed in step 2.
9. Restore power and test for proper operation.
10. Return Tamper-Proof Wrench to owner.
INSTALLATION INSTRUCTIONS
SUGGESTED MOUNTING HEIGHT
from floor to bottom of dryer:
Men
45" (114 cm)
Women
43" (109 cm)
Teenagers
41" (104 cm)
Small Children
35" (89 cm)
Accessible
37" (94 cm)
MOUNTING HARDWARE
Recommended Fastener
(not supplied):
Masonry Wall
½” Expansion Sleeve with ¼” Lag Bolt
Hollow Wall
¼” Wing Type Toggle Bolt
Wooden Wall
¼” Lag Screw With Washer
1
2
TABLE 1
TABLE 2
MOUNTING DETAILS
CLEANING / MAINTENANCE
Gently wash Cover (including air inlet holes) using a
soft cloth or sponge and a mild soap or detergent with
lukewarm water to loosen dirt and grime.
It is recommended to inspect the inside of the dryer and
clean at least twice per year. Excessive lint, dust or other
particles in the air may require more frequent cleaning.
Lint on the air inlet, the dryer Pre-Filter, HEPA filter (if
so equipped) or other internal parts of dryer will reduce
efficiency and shorten the life of the working parts.
Use the Tamper-Proof Wrench supplied and remove the
Tamper-Proof Bolt on bottom of cover, lifting upwards
to remove cover from base plate. Gently clean all
parts using a small soft brush. Remove the PreFilter,
rinse with water and dry. Inspect the HEPA Filter (if so
equipped) for any excessive debris buildup whenever
the Pre-Filter is removed.
DO NOT CLEAN THE HEPA FILTER OR ALLOW IT TO
COME INTO CONTACT WITH WATER. Reinstall the
Pre-Filter, cover and restore power.
Disconnect power to the dryer before cleaning. It is recommended that you refer to the
WHO or CDC for handling guidelines when cleaning the Pre-Filter or replacing the HEPA
filter if either may have been exposed to a contagion.
PLEASE SEE OUR WEBSITE, www.exceldryer.com FOR WARRANTY, TROUBLESHOOTING, AND PARTS INFORMATION
INSIDE:
OUTSIDE:
Gently wash Cover (including air inlet
holes) using a soft cloth or sponge and
a mild soap or detergent with lukewarm
water to loosen dirt and grime.
TO CLEAN:
