background image

8

Valet Mode

 

  Valet mode prevents the remote start feature from being activated. It also dis-

ables horn honks when locking or unlocking the doors. Valet Mode should be used 

when you do not wish for remote starting to be operated, such as when you have 

your vehicle serviced. 

To engage Valet Mode:

•  With the system “unlocked”, press and hold the Valet Switch for 3 seconds; the 

Status Light will turn on and stay on to indicate Valet Mode. The horn will honk 

once and the lights will flash twice. Once in Valet Mode, an attempt to remote start 

will result in no response. Keep this in mind if remote start stops functioning. while 

the system is in Valet Mode, the horn will honk once every time the ignition key is 

turned OFF.

•  To turn off Valet Mode, simply press & release the Valet Switch once. The Status 

Light will turn off.

Emergency Override

    If the system is locked, you cannot perform functions like transmitter or feature 

programming. If you do not have a transmitter to unlock the system, you can perform 

an emergency override to access the programming functions.

•  With the system in a locked state, simply turn the ignition key to the RUN/ON 

position and press and release the valet switch once.

Using The Valet Switch

Other Remote Start Features (cont’d)

The Status Light (Optional)

  The optional Status Light helps to visually confirms the status of the system and 

provides a high level of visual deterrence.  The Status Light is typically installed 

somewhere on the dash. Consult with your installer if there are any questions.

Normal System Status

1) Off = The remote starter system is off, in standby mode.

2)  On Constant = The system is in the Valet Mode, with the remote starter system 

disabled.

Starting System Status

 

The Status Light also indicates the remote start status:

3) Flashing Very Slow (once every 2 seconds): The system is in manual transmis-

sion remote start mode and awaiting a remote start command. 

4) Flashing Slow (once per second): Remote start is on.

4) Press LOCK on the transmitter. The engine will shut down (unless turbo timer is 

on) and the status light will flash every 2 seconds to indicate it is ready to be remote 

started.

NOTE:

 Manual transmission starting is canceled if you enter the vehicle after per-

forming the setup procedure.  After remote starting, you have 20 seconds to turn on 

the ignition key AFTER opening a door.

Summary of Contents for RS-340-EDP

















Reviews: