EWM Phoenix 355 Progress puls HP MM TKM, Operating Instructions Manual

Page: 121 / 123

Appendix
Parameter overview – setting ranges
099-005403-EW501
10.2.2022
121
JOB Procedure Material Gas Ø [mm]
330* coldArc / coldArc puls CrNi 18 8 / 1.4370 Ar-97,5 / CO2-2,5 (M12) 0,8
331* coldArc / coldArc puls CrNi 18 8 / 1.4370 Ar-97,5 / CO2-2,5 (M12) 1,0
332* coldArc / coldArc puls CrNi 18 8 / 1.4370 Ar-97,5 / CO2-2,5 (M12) 1,2
334* coldArc / coldArc puls CrNi 19 12 3 / 1.4430 Ar-97,5 / CO2-2,5 (M12) 0,8
335* coldArc / coldArc puls CrNi 19 12 3 / 1.4430 Ar-97,5 / CO2-2,5 (M12) 1,0
336* coldArc / coldArc puls CrNi 19 12 3 / 1.4430 Ar-97,5 / CO2-2,5 (M12) 1,2
338* coldArc / coldArc puls CrNi 22 9 3 / 1.4462 Ar-97,5 / CO2-2,5 (M12) 0,8
339* coldArc / coldArc puls CrNi 22 9 3 / 1.4462 Ar-97,5 / CO2-2,5 (M12) 1,0
340* coldArc / coldArc puls CrNi 22 9 3 / 1.4462 Ar-97,5 / CO2-2,5 (M12) 1,2
350 Self-shielded flux cored
wire
FCW Steel – Rutile No Gas 0,9
351 Self-shielded flux cored
wire
FCW Steel – Rutile No Gas 1,0
352 Self-shielded flux cored
wire
FCW Steel – Rutile No Gas 1,2
359 wiredArc / wiredArc pulse G3Si1 / G4Si1 Ar-82 / CO2-18 (M21) 1,0
360 wiredArc / wiredArc pulse G3Si1 / G4Si1 Ar-82 / CO2-18 (M21) 1,2
* Only in device series alpha Q and Titan XQ active.
11.2 Parameter overview – setting ranges
11.3 MIG/MAG welding
Name Display Setting range
Co
de
St
and
ar
d (
ex
w
or
ks
)
Un
it
Min. Max.
Start current -
[1]
% 0 - 200
Correction of arc length in start program P
START
-
[1]
V -9,9 - 9,9
Slope time of start program P
START
to main program P
A
-
[1]
s 0 - 20
Slope time of main program P
A
to end program P
END
-
[1]
s 0 - 20
End-crater current -
[1]
% 0 - 200
Correction of arc length in end program P
END
-
[1]
V -9,9 - 9,9
Burn-back time -
[1]
- 0 - 333
Voltage correction 0 V -9,9 9,9
Wire feed speed, absolute (main program P
A
) - [1] m/min 0,00 - 20,0
[1]
depending on the selected welding task (JOB)