-
S
5
www.evolutionbuild.com
WaRnInG:
When drilling, sanding, sawing or
grinding, dust particles will be produced. In some instances,
depending on the materials you are working with, this dust
can be particularly harmful to you (e.g. lead from old gloss
paint).You are advised to consider the risks associated with
the materials you are working with and to reduce the risk of
exposure.
You should:
- Work in a well-ventilated area.
- Work with approved safety equipment, such as dust masks
that are specially designed to filter microscopic particles.
WaRnInG:
Be sure to read and understand all
instructions. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious personal injury.
1. Know your power tool. Read operator’s manual
carefully.
Learn the applications and limitations, as well as
the specific potential hazards related to this tool.
2. always wear safety glasses or eye shields when using
this mitre saw.
Everyday eyeglasses have only impact-
resistant lenses; they are not safety glasses.
3. always protect your lungs.
Wear a face mask or dust
mask if the operation is dusty.
4. always protect your hearing.
Wear hearing protection
during extended periods of operation.
5. Inspect the machines power cord regularly and if
damaged have it repaired or replaced.
Always be aware
of the cords location.
6. always check for damaged parts.
Before further use
of the tool, a guard or other part that is damaged should be
carefully checked to determine if it will operate properly and
perform its intended function. Check for misalignment or
binding of moving parts, breakage of parts, and any other
condition that may affect the tool’s operation. A guard or
other part that is damaged should be properly repaired or
replaced at a qualified service centre. Keep guards in place
and in working order.
7. Do not abuse the cord.
Never use the cord to carry the
tool or pull the plug from the outlet. Keep cord away from
heat, oil, sharp edges or moving parts. Replace damaged
cords immediately. Damaged cords increase the risk of
electric shock.
8. always make sure that your extension cord is in good
condition.
When using an extension cord be sure to use one
that is heavy enough to carry the current that your tool will
draw. An undersized cord will cause a drop in line voltage,
resulting in loss of power and overheating.
9. Do not use the tool while tired or under the influence
of drugs, alcohol or any medication.
Following this
instruction will reduce the risk of electric shock, fire or
serious personal injury.
10. save these instructions.
Refer to them frequently
and use them to instruct others who may use this tool. If
someone borrows this tool, make sure they have these
instructions also.
11. When the correct blade to cut the material has been
fitted,
this saw is recommended for cutting mild steel,
aluminium and non-ferrous metals, wood, and plastic only.
12. Do not use saw blades with High speed steel (Hss)
or blades that are damaged or deformed.
13. Replace the table insert when worn.
14. Use only saw blades recommended by the
manufacturer
and which are the exact bore and diameter
required for this machine and conform to EN 847-1.
15. Connect your mitre saw to a dust collecting device
(I.D.Ø32mm)
when sawing material likely to cause dust.
16. select saw blades in relation to the material to be
cut.
Use only genuine Evolution or Evolution recommended
accessories.
17. Check the maximum depth of cut.
18. When sawing long work pieces,
always use extra
support to provide better support, and use clamps or other
clamping devices. To reduce the risk of injury, return the slide
carriage to the full rear position after each crosscut operation.
19. The operator is adequately trained in the use
adjustment and operation and operation of the machine.
20. Provide for adequate room lighting at your workplace
or for adequate lighting of the immediate work area.
21. When fitted with a laser no exchange with a different
type of laser is permissible.
Repairs shall only be carried
out by the laser manufacturer or an authorised agent.
22. Refrain from removing any cut-offs or other parts of
the workpiece from the cutting area whilst the machine is
running and the saw head is not in the rest position.
Never
reach around the saw blade. Turn off tool and wait for saw blade
to stop before moving workpiece or changing settings.
23. never stand on this tool.
Serious injuries could occur
when this tool tips over or when coming in contact with the
saw blade.
24. Reduce the risk of unintentional starting.
Make sure
switch is in off position before plugging in.
WaRnInG:
the operation of any mitre saw can
result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power
tool operation, always wear safety goggles or safety glasses
with side shield and a full face shield when needed.
WaRnInG:
If any parts are missing, do not operate
your mitre saw until the missing parts are replaced. Failure to
follow this rule could result in serious personal injury.
aDDITIOnal safeTY aDVICe
GB
HealTH aDVICe
GB