background image

8

www.evolutionbuild.com

®

CARE OF YOUR PURE BATTERY PACK

1. Do not charge the battery pack when the 
temperature is below 0°C (32°F) or above 
40°C (104°F).
2. Always protect the battery terminals when 
the battery pack is not used.
3. Do not short the battery pack.

Warning:

 A battery short can cause a large 

current flow, overheating, possible burns and 
even irreparable damage to the battery.

4. Do not touch the terminals with any 
conductive material.
5. Avoid storing the battery pack in a container 
with other metal objects such as nails, coins, etc.
6. Do not expose the battery pack to water 
or rain.
7. Do not store the battery pack in locations 
where the temperature may reach or exceed 
50°C (122°F).
8. Do not incinerate the battery pack even if 
it is severely damaged or is completely worn 
out. The battery pack can explode in a fire.
9. Be careful not to drop, shake or strike 
the battery.

BATTERY POWER INDICATOR

The battery pack is equipped with a power 
indicator. To show how much power is left in 
the battery pack, press the power indication 
button.

LED STATUS

BATTERY CONDITION

Only Red LED ‘on’.

Battery power very 
low. Battery needs 
to be re-charged.

Orange & Red LEDs ‘on’.

Battery power is low.

1 Green 1 Orange 
1 Red LED ‘on’.

Battery pack 
is good to use.

All LEDs ‘on’.

Battery Pack 
is fully charged.

SAFETY LABELS & SYMBOLS

WARNING! 

Do not operate machine if warning and / or 
instruction labels are missing or damaged. 
Contact Evolution Power Tools for replacement 
labels.

Symbol

Description

V

Volts

A

Amperes

Hz

Hertz

Min

-1

Speed

~

Alternating Current

No

No Load Speed
Wear Safety 
Goggles
Wear Ear Protection

Do Not Touch

Wear Dust Protection

Restriction 
of Hazardous 
Substances Directive
CE certification

Waste electrical and 
electronic equipment

Summary of Contents for Rage 7

















Reviews: