www.evolutionbuild.com
5
Operating Advice
Always securely clamp the material to be cut in the vice. To start
the tool, you must depress the main trigger switch to power the
motor. With the motor head in the raised position, switch on the
motor and allow to build up to full speed. Lower the motor head
to begin cutting. When starting a cut take care to introduce the
blade to the material slowly, using light pressure at first to keep
blade from grabbing, and then continue with normal pressure.
Do not force the tool – let the speed of the saw blade do the
work. Cutting performance will not improve by applying more
pressure on the tool, doing so may cause blade and motor life
to be reduced. Use less pressure as the blade exits through the
material. On completion of the cut, return the motor head to its
upright position and switch off the power. Keep the tool clean
of metal chips and other dirt and debris.
Work Piece Clamping
Position the work piece in the vice so that if a jam occurs, the
blade will not tend to throw it from the vice. Clamp it securely.
Angles should be in an inverted position so that the point of the
section is uppermost. The saw cuts most efficiently if the blade
is cutting the thinnest section of the material (FIG 2 - P12).
Maintenance & Troubleshooting
Keep tool and cord clean. Regularly vacuum or blow out
the motor unit to keep its ventilation clear, also check that
the machine is well lubricated. Inspect weekly. Avoid using
cleaning products, which include benzene, trichloroethelene,
chloride, and ammonia as these can damage plastic parts.
In case of electrical or mechanical malfunction, immediately
switch off the tool and disconnect the plug.
Brush Inspection & Replacement
Excessive sparking may indicate the presence of dirt in the motor
or worn out carbon brushes. Check for wear after the first 50
hours of use and then at 10 hours use intervals. Replace when
they reach 6mm. The brush holders are located on the motor
housing opposite each other and unscrew to allow access to the
brushes. For all other service and maintenance, take the machine
to an authorised service centre after typically 60 cutting hours,
dependent upon the type of workload it has endured.
Lubrication
Your machines motor bearings are lubricated at the factory with
sufficient lubricant to last for the lifetime of the unit under normal
operating conditions. Other movable parts can be lubricated with
light machine oil as necessary. It is recommended that the machine
be taken to the nearest SERVICE CENTER / DEALER at least once
a year for a thorough cleaning & lubrication. Please contact 0114
251 1022 (UK) or 866-EVO-TOOL (US) for assistance and /or
information. All repairs and servicing made by these centres are
fully guaranteed against defective materials and workmanship.
12 month limited warranty. Evolution power tools reserves.
The right to make improvements and modifications to
design without prior notice.
Evolution Power Tools will, within twelve (12) months
from the original date of purchase, repair or replace any
goods found to be defective in materials or workmanship,
provided the product warranty registration card has
been returned to Evolution Power Tools. This warranty
is void if the tool being returned has been used to
cut materials beyond the recommendations in the
Instruction Manual or if the saw has been damaged by
accident, neglect, or improper service. This warranty
does not apply to machines and / or components which
have been altered, changed, or modified in any way,
or subjected to use beyond recommended capacities
and specifications. Electrical components are subject
to respective manufacturers’ warranties. All goods
returned defective shall be returned prepaid freight to
Evolution Power Tools. Evolution Power Tools reserves
the right to optionally repair or replace it with the same
or equivalent item. There is no warranty – written or
verbal – for saw blades. In no event shall Evolution
Power Tools be liable for loss or damage resulting
directly or indirectly from the use or merchandise or
from any other cause. Evolution Power Tools is not liable
for any costs incurred on such goods or consequential
damages. No officer, employee or agent of Evolution
Power Tools is authorised to make oral representations
of fitness or to waive any of the foregoing terms of sale
and none shall be binding on Evolution Power Tools.
Questions relating to this limited warranty should be
directed to the company’s head office, or call the appropriate
Helpline number.
Accessories – Genuine RAGE Technology Blades
355mm TCT Multipurpose Blade
Notice: Fair wear and tear and damage caused by
misuse is not covered under the 12 month guarantee.
METAL CUTTING SAW SAFETY
UK
12 MONTH WARRANTY
UK