Evolution Aqua evoUV evo110 Installation And Operating Manual Download Page 15

15

CONNECTION TO THE ELECTRICITY SUPPLY

Electrical installations must be done by a qualified electrician.

The power supply must meet the specifications on the product.  
The cores in the supply cable are coloured in accordance with the 
following code:

UK / EU:  

 

Brown = Live 
Blue = Neutral 
Green / Yellow = Earth

Do not use the supply cable to lift the UV as this may cause damage. 

WARNING

 - A Residual Current Device (RCD), also known as the Residual Current Circuit 

Breaker (RCCB), with a tripping current not exceeding 30mA must be installed in the 
supply circuit. A means of disconnection from the supply having a contact separation of at 
least 3mm in all poles must be incorporated in the wiring.

Caution:

 Use in the area of a swimming pool only if the installation complies with the 

relevant wiring regulations. Please consult a qualified electrician.

All electrical installations and wiring must be adequately protected to prevent  
any damage.

Enough electrical cable is supplied with the unit to connect to the mains electric. This unit 
must be connected to permanent wiring. A switch with 3mm contact separation must be 
provided in the fixed wiring to provide disconnection from the electricity supply.

It is recommended that the UV unit is wired in conjunction with the pump so that when the 
pump is turned off, so is the UV unit.

USA SPECIFIC

GROUNDING INSTRUCTIONS

 - This appliance must be grounded. In the event of a 

malfunction or breakdown, grounding will reduce the risk of electric shock by providing a 
path of least resistance for electric current. This appliance is equipped with a cord having 
an appliance-grounding conductor and a grounding plug. The plug must be plugged into 
an appropriate outlet that is installed and grounded in accordance with all local codes and 
ordinances.

WARNING

 - Improper connection of the appliance-grounding conductor can result in a 

risk of electric shock. Check with a qualified electrician or service representative if you 
are in doubt whether the appliance is properly grounded. Do not modify the plug provided 
with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified 
technician.

USA WIRING

Black = Live 
White = Neutral 
Green = Earth

Downloaded from http://www.watergardeningdirect.com

Summary of Contents for evoUV evo110

























Reviews: