manualshive.com logo in svg

evoheat Polaris LA 60, Installation And Instruction Manual

Share
Download
evoheat Polaris LA 60 Installation And Instruction Manual Download Page 27

23

Operation and Use

Note:

①

:Fault code

②

:Fault name

③

:Occurrence time of the fault,Day, month and year   hour: second (s)

④

:Click this key to clear all fault records

meaning

default

adjust(yes/no) 

Parameter table

Return water temp. 

Setting( Hot water)

yes

55

℃

parameter

Return water temp. 

Setting(Heating)

yes

40

℃

R01

R02

24

6.1 Maintenance

Check the water supply and air vent frequently, to avoid lack of water or air in the water loop.
Clean the water filter in a certain period to keep good water quality. Lack of water and dirty 
water can damage the unit. The heat pump will start the water pump per 72 hours when it is 
not running, to avoid freezing. 

Keep the unit in a place which is dry and clean, and has good ventilation. Clean the heat 
exchanger in 1 or 2 month and keep good heat exchange rate and save energy.

Check each part of the unit and the pressure of the system. Replace the failure part if there 
is any, and recharge the refrigerant if it is needed.

If the heat pump is not used for a long time, please drain out all the water in the unit and 
seal the unit to keep it good.  Please drain the water from the lowest point of the heat 
exchanger to avoid freezing in winter.  Water recharge and full inspection on the heat 
pump is needed  before it is restarted. 

Check the power supply and the electrical system, make sure the electrical components are 
good, the wiring is well. If there is any part failed with wrong action or smell, please replace 
in time.

The water loop of the heat pump MUST be protected from freezing in winter time. Please 
pay attention to below suggestions. Nonobservance on below suggestion will invalid the 
warranty  for the heat pump.

(1)  Please do not shut off the power supply to the heat pump in winter.  When the air 

      temperature is below 0 

℃

,  if the inlet water temperature is above 2 

℃

 and below 4

℃

,

      the water pump will start for freezing protect, if the inlet water is lower than 2 

℃

, the 

      heat pump will run for heating. 
     

Please drain out the water in the super heater of the heat pump unit in winter, when the 
super heater is not used, in case it is heat pump with super heater.

Troubleshooting and extra information

Note:

①

:Fault code

②

:Fault name

③

:Occurrence time of the fault,Day, month and year   hour: second (s)

④

:Click this key to clear all fault records

Summary of Contents for Polaris LA 60





































Reviews:

No comments

Brands by name

Popular brands

Load more brands