background image

1. The unit can only be repaired by qualified installer centre personnel or an authorised

dealer.

for Europe market

2. This appliance is not intended for use by persons (including children) with reduced physical

sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. 

for Europe market

Children should be supervised to ensure that they do not play with the appliance.

3. Please make sure that the unit and power connection have good earthing, otherwise may 

cause electrical shock.

4. If the supply cord is damaged, it must be replaced by the manufacturer or our service agent

or similarly qualified person in order to avoid a hazard.

5. Directive 2002/96/EC (WEEE):

The symbol depicting a crossed-out waste bin that is underneath the appliance indicates
that this product, at the end of its useful life, must be handled separately from domestic
waste, must be taken to a recycling centre for electric and electronic devices or handed 
back to the dealer when purchasing an equivalent appliance. 

6. Directive 2002/95/EC (RoHs): This product is compliant with directive 2002/95/EC (RoHs)

concerning restrictions for the use of harmful substances in electric and electronic devices.

7. The unit CANNOT be installed near the flammable gas. Once there is any leakage of the gas

, fire can be occur.

8. Make sure that there is circuit breaker for the unit, lack of circuit breaker  can lead to 

electrical shock or fire.

9. The heat pump located inside the unit is equipped with an over-load protection system. It

does not allow for the unit to start for at least 3 minutes from a previous stoppage.

10. The unit can only be repaired by the qualified personnel of an installer center or an 

authorized dealer. 

for North America market

11. Installation must be performed in accordance with the NEC/CEC by authorized person only.

for North America market

12. USE SUPPLY WIRES SUITABLE FOR 75

.

13. Caution: Single wall heat exchanger, not suitable for potable water connection.

Caution & Warning

6.APPENDIX

1

2

Summary of Contents for Fusion 13






















Reviews: