evoheat Evo270-1 Installation & Operation Manual Download Page 16

  [email protected] 

  1300 859 933 

  www.evoheat.com.au 

 

 

 

 

 

 

Evo270-1 Manual 

Page 15  

8.2 Use of the P&T Valve 

 

The P&T valve is used to prevent the temperature or pressure becoming too high inside the tank. When 
the temperature or pressure reaches the set value, the valve will open automatically to force the pressure 
or temperature to decrease 

The handle of the safety valve should be tested once every six months to remove the calcium carbonate deposits and 
guarantee there is no blockage in the device. Take care to avoid burns as the temperature of the discharging water is 
very high.  

Vent pipes should be thermally insulated to prevent safety risks caused by freezing pipes in winter. 

P&T valve: Model: PTR-20, action temperature: 

99˚

C, action pressure:0.85MPa  

 

WARNING:

 Failing to operate the relief valve easing gear at least once every six months may result in 

the water heater exploding. Continuous leakage of water from the valve may indicate a problem with the 

water heater. 

 

8.3 Using the Overheating Protector 

The overheating protector is used to turn the power off in an emergency 
or with power supply issues, preventing the water from being heated too 
high. 
 
A thermal cut-out could indicate a possibly dangerous situation. Do not 
reset the thermal cutout until the unit has been serviced by a qualified 
technician. Contact EvoHeat for a service if this occurs before 
attempting to reset. 
 
To return the unit to its normal operation status by resetting manually: 
 

a)  To access the overheat protector, remove the front dark grey 

controller panel. 

b)  Remove the 3 screws on the front panel and push the front 

cover upwards. 

c) 

Remove the remaining screws which cover the overheat 
protector panel.

 

 

Remove the screws and open the cover 

 

 

Press the red button to reset

 

 

8.4 Draining the Water Tank 

1.  Close the cold-water inlet valve into the Evo270-1. 

2.  Open a hot water tap inside the premises. 

3.  Undo the drain plug on the base of the unit to drain 

the water from the system. 
 

8.5 Earthing Methodology 

 

 

 

The water from the hot water tap and the drain plug 

will be hot. Be careful of burns and scalds. Wear 

protective clothing. 

Summary of Contents for Evo270-1



















Reviews: