EVoCharge EVoInnovate EVO32-300-001 User Manual & Installation Manual Download Page 3

                                                                                           User Manual Rev 1.0 

 

EVoInnovate EVSE User Manual & Installation Guide 
www.evocharge.com 

Repair and Maintenance Clause 

 

All EVoCharge products do not require routine maintenance however, periodic inspections should be conducted 
to ensure that all parts remain in good working order and no damage exists.  Do not attempt to open, 
disassemble, repair, tamper with, or modify any components of the products 

 the products are not user 

serviceable.  Contact EVoCharge for any repairs.   

 

Only licensed electricians can repair or maintain the charging station.  It is forbidden for general users to repair or 
maintain it.  Turn off input power before performing any repairs or maintenance to the charging station. 

  

FCC Declaration of Conformity 

 

This charging station complies with part 15 of the FCC Rules. Changes or modifications the charging 
station not expressly approved by the manufacturer could void FCC compliance. 

 

Operation is subject to the following two conditions: (1) This charging station may not cause harmful 
interference, and (2) this device must accept any interference received, including interference that may 
cause undesired operation. 

OVERALL WARNINGS & CAUTIONS 

 

 
 

 

 

 

 

 

 

 

 

 

WARNING: RISK OF ELECTRIC SHOCK 
Basic precautions should always be followed when using electrical products, including the 
following: 

 

Read all the instructions before using this product. 

 

This device should be supervised when used around children. 

 

Do not put fingers into the EV connector. 

 

Do not uses this product if the flexible power cord or EV cable is frayed, has broken 
insulation, or any other signs of damage. 

 

Do not use this product if the enclosure or the EV connector is broken, cracked, open, or 
shows any other indication of damage. 

 

WARNING: RISK OF ELECTRIC SHOCK 
Improper connection of the equipment grounding conductor can result in a risk of electric 
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the 
product is properly grounded. 

 

 

 

 

WARNING: RISK OF ELECTRIC SHOCK 

 

Do not touch live electrical parts. 

 

Incorrect connections may cause electric shock. 

WARNING: This equipment is intended only for charging vehicles that do not require 

ventilation during charging. Please refer to your vehicle’s owner’s manual to determine 

ventilation requirements. 

 

Summary of Contents for EVoInnovate EVO32-300-001























Reviews: