Evikon PluraSens E2648-NH3-S User Manual Download | Manualshive

Page: 12 / 21

background image

E2648-NH3-S

Rev 22.06.2021

NOTE! The outputs are not galvanically isolated from the external power supply and share
a common 0V. Allowed load resistance limits are stated in the Speciﬁcations table. To
power the instrument from an external power source, connect terminals 0V and +U to the
source. If the integrated mains power supply module is used, connect terminals L and N to
the mains.

NOTE! Actuator short-circuits should be avoided, to protect the instrument relays using
external fuses or safety switches.

Correct and incorrect cabling for 24 VAC

12

«
...
10
11
12
13
14
...
»

Summary of Contents for PluraSens E2648-NH3-S






















Reviews:

No comments

Related manuals for PluraSens E2648-NH3-S

Brand: Magnetek Pages: 2

Brand: Omega Pages: 2

Brand: Yaesu Pages: 120

Brand: Yaesu Pages: 35

Brand: Sytech Pages: 6

Brand: Tachosys Pages: 17

Brand: GE Pages: 40

Brand: BD Sensors Pages: 2

Brand: ClearSounds Pages: 30

Brand: Charles Pages: 13

Brand: Shure Pages: 4

Brand: Telemotive Pages: 31

Brand: Yaesu Pages: 64

Brand: Vaisala Pages: 58

Brand: Clas Ohlson Pages: 4

Brand: Honeywell Pages: 48

Brand: Honeywell Pages: 2

Brand: Honeywell Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands