18
Compliance Information
FCC Compliance Information
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna, or (2) Increase the separation between the equipment and receiver, or
(3) Connect the into an outlet on a circuit different from that which the receiver is connected, or (4) consult the dealer or
an experienced radio/TV technician for help. Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment
.
Federal Communications Commission (FCC) Radiation Exposure Statement
This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE 1-1999 and had
been tested in accordance with the measurement methods and procedures specified in IEEE 1528-2013.
Contains Transmitter Module FCC ID : 2AG9J8265NG
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna
or transmitter.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible.
This device is restricted to indoor use.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
End user must follow the specific operating instructions for satisfying RF exposure compliance.
CE Compliance Information
Generic Radiation Interference Standard for Information Technology Equipment. (EN 55032: 2015/AC:2016, Class B),
(EN 61000-3-2: 2014), (EN 61000-3-3: 2013). Warning: This is a Class B product. In a domestic environment this
product may cause radio interference in which case the user may be required to take adequate measure. Generic
Immunity Standard for Information Technology Equipment.(EN 55024: 2010).
Trademark & Copyright Information
2001-2017 EVGA Corp. EVGA, the EVGA logo and combinations thereof are trademarks of EVGA Corp. All brand
names, company names, service marks, logos, and trademarks of the company, or its affiliates or licensors are
trademarks or registered trademarks of the company or its subsidiaries, affiliates or licensors in the US and other
countries. Other company, products and service names may be trademarks or service marks of others. EVGA reserves
the right to terminate this license if there is a violation of its terms or default by the Original Purchaser. Upon termination,
for any reason, all copies of Software and materials must be immediately returned to EVGA and the Original Purchaser
shall be liable to EVGA.com CORP for any and all damages suffered as a result of the violation or default.
Legal Information
All material including but not limited to, text, data, design specifications, diagnostics, graphics, logos, reference boards,
files, images, drawings, and software including this document and the software itself (together and separately) is owned,
controlled by, licensed to, or used with permission by EVGA Corporation and is protected by copyright, trademark, and
other intellectual property rights. All is being provided “as is”, EVGA Corporation makes no warranties, whether express
or implied, statutory or otherwise with respect to the materials and expressly disclaims all implied warranties of non-
infringement, merchantability, and fitness for a particular purpose. In no event shall the liability of EVGA Corporation for
claims arising from the use of the materials by anyone exceed the original purchase price of the materials (or
replacement of the materials at EVGA Corporation’s option). All information furnished is believed to be accurate and
reliable. However, EVGA Corporation assumes no responsibility for the consequences of use of such information or for
Summary of Contents for SC17G GAMING
Page 11: ...11 ...
