Everwell METH-16 User And Installation Manual Download Page 3

D

uring  the installation of the indoor and 

outdoor units the access to the working area 

should be forbidden to children.

Unforeseeable accidents could happen.

M

ake sure that  the base of  the outdoor unit  is

firmly fixed.

C

heck that air  cannot enter the refrigerant 

system and check for  refrigerant leaks when  

moving the air con ditioner. 

SAFETY RULES AND RECOMMENDA

TIONS FOR THE INSTALLER 

C

arry out a test cycle after installing the air 

conditioner and record the operating data. 

T

he ratings of the fuse installed in the built  

incontrol unit are  T 5A /  250V    . 

T

he user must  protect  the  indoor unit  with a 

fuse of suitable capacity for the maximum input 

current or with another overload protection

device. 

E

nsure that  the mains voltage corresponds  to 

that stamped on the rating plate. Keep the switch 

or power plug clean. Insert the power plug 

correctly and firmly into the socket, thereby 

avoiding the risk of electric shock or fire due to 

insufficient contact. 

C

heck that the socket  is suitable for the plug , 

otherwise have the socket changed. 

D

o not install the appliance at  a  distance  of 

less than 50 cm from inflammable substances 

(alcohol, etc.) Or from pressurised containers 

(e.g. spray cans). 

I

f  the appliance  is used  in areas without the 

possibility of ventilation, precautions must be 

taken to prevent any leaks  of refrigerant  gas

from remaining in the environment and creating 

a danger of fire 

T

he packaging materials  are  recyclable  and 

should  be  disposed  of  in the separate waste 

bins .Take the air conditioner at the end of  its 

useful life to a special  waste collection centre 

for disposal. 

O

nly use the air conditioner  as  instructed  in 

this booklet. These instructions are not intended  

to cover every possible condition and situation . 

As  with  any electrical  household appliance ,  

common sense and caution are therefore always  

recommended for installation, operation and 

maintenance. 

T

he appliance must be installed in accordance

with applicable national regulations. 

B

efore accessing the terminals , all the  power 

circuits must be disconnected from the  power 

supply. 

R

ead this guide before installing and using  the

appliance.

1

T

he appliance must be fitted with means for 

disconnection from the supply mains having a 

contact separation in all poles that provide full 

disconnection under overvoltage category III 

conditions, and these means must be incorporated 

in the fixed wiring in accordance with the wiring 

rules. 

T

he appliance shall be installed in accordance 

with national wiring regulations.

T

his appliance can be used by children aaged  

from  8 years and above and persons with 

reduced physical, sensory or mental capabilities 

or lack of experience and knowledge if they 

have been given supervision or instruction 

concerning use of the appliance in a safe way 

and understand the hazards involved. Children 

shall not play with the appliance. Cleaning and 

user maintenance  shall  not  be made  by 

children without supervision.

T

he air conditioner must be installed by 

professional or qualified persons.

Summary of Contents for METH-16






























Reviews: