evertz X1201-AES4 Manual Download

Page: 27 / 102

X1200 Series Router Manual

INSTALLATION

Revision 1.3.2

Page 2-3

Inputs for the 1A and 1B busses are on the panel connected to the

AES AUDIO 1 I/O

connector. Outputs

1 and 2 of the AES A and AES B sections are identical outputs from the 1A and 1B busses respectively.
Inputs for the 2A and 2B busses are on the panel connected to the

AES AUDIO 2 I/O

connector. Outputs

1 and 2 of the AES A and AES B sections are identical outputs from the 2A and 2B busses respectively.
(See Figure 6-12 and Figure 6-13)

In the 2(12x2) mode there are two 12 x 2 router sections. The inputs and outputs from the 1A and 1B
busses follow the V1 buss and are located on the on the breakout panel connected to the

AES AUDIO 1

I/O

connector. The inputs to 2A and 2B audio busses are internally connected to the inputs of the 1A and

1B audio busses respectively (The inputs on the breakout panel connected to the

AES AUDIO 2 I/O

connector are not used in this mode). The outputs from the 2A and 2B busses follow the V2 buss and are
located on the on the breakout panel connected to the

AES AUDIO 2 I/O

connector. (See Figure 6-10 and

Figure 6-11)

2.1.3.3. Audio Connections on Router Models with the AES4 Option Fitted.

Routers fitted with the AES4 option are shipped with two breakout panels. The inputs and outputs from
the 1A and 1B busses and are located on the on the breakout panel connected to the

AES AUDIO 1 I/O

connector. The Audio from the selected Audio Input buss associated with video buss 1 will be available
on output 1 of AES A and AES B sections of the breakout panel. On the X1202ABO used with the X1202

routers, audio from the selected Audio Input buss associated with video buss 2 will be available on output
2 of AES A and AES B sections of the breakout panel. (See Figure 6-8 and Figure 6-9) On the
X1201ABO used with the X1201 routers, outputs 1 and 2 are identical. (See Figure 6-3)

The inputs and outputs from the 2A and 2B busses and are located on the on the breakout panel
connected to the

AES AUDIO 2 I/O

connector. The Audio from the selected Audio Input buss associated

with video buss 1 will be available on output 1 of AES A and AES B sections of the breakout panel. Audio
from the selected Audio Input buss associated with video buss 2 will be available on output 2 of AES A
and AES B sections of the breakout panel. On the X1201ABO used with the X1201 routers, outputs 1 and
2 are identical.

2.1.4. Reference Connections
VIDEO REF

is a high impedance loop through for connecting an analog video or tri-level sync (X1200H

series only) reference. The

REFERENCE

menu is used to select the correct type of video

reference being used.

DARS REF

(X1202S-AES-SS and X1202S-AES4-SS only) is a high impedance loop through for a Digital

Audio Reference Signal. The

REFERENCE

menu is used to select the use of the DARS signal

when the Softswitch



is enabled on Softswitch



routers.

2.1.5. Remote Control Connections
REMOTE CTL

This 9 pin female D connector provides an RS-232 serial interface used for updating the

firmware or external serial remote control. The

Setup

menu is used to configure the REMOTE

CTL port for external control or firmware updating. (See section 3.3.). This port is wired at the
factory as an RS232 DCE port as shown in Table 2-1.

The port can also be used to connect a remote control panel to the router. To connect to a

remote panel the port must be configured as a SMPTE 207M Tributary as shown in Table 2-2.
To reconfigure the port the user must remove the top cover and reposition jumper J26 so that it
is on pins 2 & 3 (toward header J23) and move the ribbon cable to header J23.