evertz 9821EMR-AG-HUB User Manual Download Page 15

Page: 15 / 58

9821EMR-AG-HUB

User Manual

Revision 0.1

Page - 3

PHYSICAL CONNECTION

9821EMR-AG-HUB is occupying 1RU rack space and there are connections at the back and front of

the unit for different purposes.

2.1. FRONT PANEL

Figure

2-1 : 9821EMR-AG-HUB Front Panel Connections

Front of the unit has the following connections:

Number 1 and 2:

BNCs for reference in and loop out

Number 3:

18 SFP cages for mini din or fiber SFPs

Number 4:

Two SFP cages for Main and Backup Q-SFPs

Number 5:

Top FC for 9821EMR-AG-HUB communication and upgrade

Number 6:

Bottom FC for Dante modules’ communications and upgrade

Number 7:

Main and backup PSUs

2.2. REAR PANEL

Figure

2-2 : 9821EMR-AG-HUB Rear Panel Connections

Number 8:

Main and backup (optional) power supplies

Number 9:

Top FC Ethernet port

Number 10:

Bottom FC Ethernet port

Number 11:

Dante module with main and backup ports

Number 12:

Fan module

This device must be power cycled after rebooting or upgrading either frame

controller.

Summary of Contents for 9821EMR-AG-HUB



























































Search results

Summary of Contents for 9821EMR-AG-HUB

Reviews:

Brands by name

Popular brands

evertz 9821EMR-AG-HUB, User Manual

Search results

Summary of Contents for 9821EMR-AG-HUB

Reviews:

Brands by name

Popular brands