evertz 7707VT13-4-HS Manual Download Page 14 | Manualshive

Page: 14 / 24

background image

7700 MultiFrame Manual

7707VT-4-HS Quad SD/Dual HD-SDI Fiber Transmitter

Page -

10

Revision

1.4

VIDEO 2 STATUS:

Green

indicates the presence of a valid signal on channel 2.

Yellow

indicates that the signal connected to channel 2 conflicts with the currently

selected input mode (see section 4.2.4).

Red

indicates the detection of bit errors on channel 2 (when bit error detection is

enabled – see section 4.2.7).

LED Off

indicates signal loss on channel 2.

VIDEO 3 STATUS:

Green

indicates the presence of a valid signal on channel 3.

Yellow

indicates that the signal connected to channel 3 conflicts with the currently

selected input mode (see section 4.2.4).

Red

indicates the detection of bit errors on channel 3 (when bit error detection is

enabled – see section 4.2.7).

LED Off

indicates signal loss on channel 3.

VIDEO 4 STATUS:

Green

indicates the presence of a valid signal on channel 4.

Yellow

indicates that the signal connected to channel 4 conflicts with the currently

selected input mode (see section 4.2.4).

Red

indicates the detection of bit errors on channel 4 (when bit error detection is

enabled – see section 4.2.7).

LED Off

indicates signal loss on channel 4.

4.2.

DOT-MATRIX DISPLAY / CARD STATUS AND CONTROLS

Additional status monitoring and controls are provided via the 4-digit dot-matrix display located at the card-
edge. The card-edge toggle-switch (see Figure 4-1) is used to navigate through the display menus and the
pushbutton is used to select options. Figure 4-2 provides a quick reference to the display menu structure.

«
...
12
13
14
15
16
...
»

Summary of Contents for 7707VT13-4-HS

























Reviews:

No comments

Related manuals for 7707VT13-4-HS

Brand: Icom Pages: 26

Brand: Omni Pages: 2

Brand: Icom Pages: 32

Brand: M-system Pages: 3

Brand: Yaesu Pages: 15

Brand: Endress+Hauser Pages: 26

Brand: Vector Pages: 3

Brand: M-system Pages: 4

Brand: Ocean Signal Pages: 28

Brand: Kimo Pages: 32

Brand: Icop Pages: 7

Brand: NIVELCO Pages: 36

Brand: Procare Pages: 2

BTL7-A M Series

Brand: Balluff Pages: 160

Brand: Icom Pages: 40

Brand: Icom Pages: 60

Brand: Icom Pages: 96

Brand: Icom Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands