- 5 -
c. If a device signal is received in Test Mode the doorbell would sound and
indicate with LEDs 1 to 9 (LED 1 – 9 indicates Sensor Zone 1 – 9, Remote
1 – 9, or Tag 1 – 9. Other indications would be LED 0)
If the device is a sensor, the Sensor Type will be indicated as below:
Arm LED on: indicates the Sensor will only trigger when Fully Armed
Partial LED on: indicates the Sensor will trigger when Fully Armed or
Partial Armed
Alarm LED on: indicates the Sensor will trigger an immediate alarm (24
hours) when Fully Armed / Partial Armed / Disarmed.
d. Press 7 for 3 or more seconds during Test Mode would display the GSM
signal strength indicated as: LED 1 (Good), LED 2 (Normal), LED 3 (Poor),
LED 4 (No Signal / SIM card registration failure / No SIM card).
e. Press 8 for 3 or more seconds during Test Mode would send a System On
/ Off command from the Wireless Siren.
f. Press 9 for 3 or more seconds during Test Mode would send a test SMS
(including the current Alarm Mode, Delay Time, Siren On/Off, and Alarm
Time) to the host mobile phone number.
3-7 Alarm Procedure:
When an alarm is triggered the Alarm LED will flash and the alarm will
sound (depending on your Alarm Type and Alarm Time settings) with an
SMS / call notification (depending on your Alarm message and SMS
setting). LEDs 1 – 9 will also indicate Sensor Zone 1 – 9, Remote 1 – 9, or
Tag 1 – 9. LED 0 will light on for other situations. For Alarm LED, enter
“Pa Disarm Key” to clear Alarm Memory. The default time for
Siren Alarm is 3 minutes.
3-8 Open Door / Window Alert:
When set to On and entering Fully Armed or Partial Armed, the door /
window sensors will be checked depending on alarm mode. If sensor
shows Open then the device will beep 10 seconds, and the LED will show
1 – 9 for Sensors 1 – 9 (0 for other Sensor Zones). After the alert has
ended it will enter the configured warning procedure (if all doors / windows
are normal the alert sounds will turn off).
You may also check beforehand:
Pressing the Arm Key will check all doors and windows under Fully Armed
and display LED opened doors or windows for 3 seconds.
Pressing the Partial Arm Key will check all doors and windows under
Partial Armed and display LED opened doors or windows for 3 seconds.
3-9 RF Anti-Jamming Function
When Anti-jamming is set to on, the device will send an SMS to the Host
Phone Number when RF jamming is detected under Arm Mode.
3-10 One Key Alarm Mode
Under Disarm Mode:
Press Arm Key for 3 or more seconds to enter Arm Mode;
Press Partial Arm Key for 3 or more seconds to enter Partial Arm Mode.
3-11 Disarm Threat Password
Threat Password is your normal pa 1.
For example: normal password 1230 will have a threat password of 1231
Normal password of 9999 will have a threat password of 0000.
An SMS will be sent to the Host Phone Number when using a threat
password to disarm.
3-12 Sensor Low Battery Indication
When a Sensor Low Battery signal is received an SMS will be sent to Host
Phone Number (The sensor will send a second SMS after a minimum
interval of 7 days).
3-13 Restore to factory settings with the Reset button:
a. Turn off all power
b. Press and hold the Reset button (next to the DC-Jack) then restart the
device. One beep will sound.
c. 5 beeps will sound to indicate the device has been restored to factory
settings.
d. Default password is: 1234. For other default values please see the Quick
Guide.
4. Alarm Message Playback and SMS Functions
Device SIM card setup and installation instructions:
a. Unlock the SIM card before use. PIN code or PUK code not required.
b. Do NOT set the SIM card phone number to host phone number or regular
SMS phone number.
c. Ask your local carrier to disable voice message function of this SIM card.
d. As alarm messages and sending SMS require fees, please inquire with
your local carrier about their charging standards.
