background image

www.event-lighting.com.au 

 

 

Set up DMX channel from control panel. When fixture is in 4 DMX channel mode, you will only able to set up from Ch1 

to Ch4. When fixture is in 31 DMX channel mode, you will only able to set up from Ch1 to Ch31.     

Use “Up” and “Down” button to set up each channel value from <000> to <255>, press “Enter" to save new setting. 

 

Auto Mode 

This fixture has 37 built-in programs. Enter "Auto" mode, use “Up” and “Down” button to select the built-in programs 

from <Auto 00> to < Auto 36>, then press the "Enter" to confirm. Use “Up” and “Down” button to select the operating 

speed of the program from <000> to <255>, press “Enter" to save new setting. You have to use “Effect on Auto” mode 

to adjust the brightness, also add strobe effect and adjust strobe speed to auto run. 

 

Effect on Auto 

Use “Effect on Auto” to switch on dimmer and strobe function to auto mode. Enter “Effect on Auto” mode, use “Up” and 

“Down” button to select dimmer level from <000> to <255>, and then press the "Enter" to confirm. Use “Up” and “Down” 

button to select strobe speed from <000> to <255>, press “Enter" to save new setting. 

 

Master/Slave Mode 

Set the master fixture to auto or manual modes.   

Enter “Master” mode, use “Up” and “Down” button to select “Yes”, and then select <slave>, press “Enter” to set fixture to 

slave mode.   

Use DMX cable to link master and slave fixture together. 

 

DMX Data

 

When there is a <*> flashing, the fixture is not receiving any DMX signal. A solid <*> indicates DMX signal is being 

received. DMX takes priority over all other functions when a signal is being received. 

Once DMX signal is lost, the fixture will revert back to the original setting, which also could be DMX or Manual or 

Automatic mode.   

DMX Chart

 

4 channels Mode 

Channel 

Value 

Function 

000-255 

Red: 0% to 100% 

000-255 

Green: 0% to 100% 

000-255 

Blue: 0% to 100% 

000-255 

White: 0% to 100% 

5 channels Mode 

Channel 

Value 

Function 

 

000-005 

No function 

006-250 

Strobe speed from slow to fast at RGBW full on 

251-254 

RGBW full on 

255 

Special strobe effect at RGBW full on 

 

000-005 

No function 

006-250 

Strobe speed from slow to fast at red full on 

251-255 

Red full on 

 

000-005 

No function 

006-250 

Strobe speed from slow to fast at green full on 

Summary of Contents for WIP1320










Reviews: