manualshive.com logo in svg

EUTECH INSTRUMENTS ECOSCAN SALT 6 METER, Instruction Manual, Page: 34 / 40

Share
Download
EUTECH INSTRUMENTS ECOSCAN SALT 6 METER Instruction Manual Download Page 34

Instruction Manual                                                                                                                                   Salt 6 

30

 

11 ACCESSORIES 

Replacement Meter and Meter accessories 

Item Eutech 

Instruments 

Ordering Code 

Oakton Instruments 

Ordering Code 

Salt 6 portable salinity meter 
complete with conductivity probe 
of k=1.0 (CONSEN91B).  

ECSALT603K 35606-20 

3 ring SS, Ultem body Electrode 
with ATC & BNC plug (for CON 
6), cell constant = 1.0, x110 mm, 
1m cable length 

ECCONSEN91B 35606-55 

Carrying kit with calibration 
standards and rinse bottle.  

ECECOCONKIT 35632-97 

 

Calibration Solutions 

 

 

Item Oakton 

Instruments 

Ordering Code 

4.487 ppt Sodium 
Chloride (NaCl) 
Calibration Solution in 
500-ml leak-proof bottle.  

00653-89 

8.532 ppt Sodium 
Chloride (NaCl) 
Calibration Solution in 
500-ml leak-proof bottle.  

00653-50 

48.384 Sodium Chloride 
(NaCl) Calibration 
Solution in 500-ml leak-
proof bottle.  

00653-32 

 

Item 

Eutech 

Instruments 

Ordering Code  

5 ppt (0.5%) Sodium 
Chloride (NaCl) 
Calibration Solution in 
480-ml leak-proof bottle.  

ECNACL5PPT 

25 ppt (2.5%) Sodium 
Chloride (NaCl) 
Calibration Solution in 
480-ml leak-proof bottle.  

ECNACL25PPT 

45 ppt (4%) Sodium 
Chloride (NaCl) 
Calibration Solution in 
480-ml leak-proof bottle.  

ECNACL45PPT 

Summary of Contents for ECOSCAN SALT 6 METER









































Reviews:

No comments