background image

Page 45/72

October 2019

W11E | Operation manual

8

Inverter  1
Over 
Temperature 

Blocking All 

• Operation 

in high temp environment. 

• Operation with high load. 
• Wrong mounting of the controller 

heat sink. 

• Wrong working of controller cooling 

system. 

Inverter 1 power 
module temperature 
above +100°C. 

Bring power module 
temperature of inverter1 
below 100°C and cycle 
key switch. 

9

Inverter  2 
Over 
Temperature

Blocking All 

• Operation 

in high temp environment. 

• Operation with high load. 
• Wrong mounting of the controller 

heat sink. 

• Wrong working of controller cooling 

system. 

Inverter 2 power 
module temperature 
above +100°C. 

Bring power module 
temperature of inverter2 
below 100°C and cycle 
key switch. 

10

Inverter 1
High 
Temperature

Limiting 

All 

• Operation in high temp environment. 
• Operation with high load. 
• Wrong mounting of the controller 

heat sink. 

• Wrong working of controller cooling 

system. 

Inverter 1 power 
module temperature 
above +80°C. 

Bring power module 
temperature of inverter1 
below 80°C. 

11

Inverter 2
High 
Temperature 

Limiting 

All 

• Operation in high temp environment. 
• Operation with high load. 
• Wrong mounting of the controller 

heat sink. 

• Wrong working of controller cooling 

system. 

Inverter 2 power 
module temperature 
above +80°C. 

Bring power module 
temperature of inverter2 
below 80°C. 

12

Inverter 1
Under 
Temperature

Blocking 

All 

Operation in low temp environment. 

Inverter 1 power 
module temperature 
below -40°C. 

Bring inverter 1 power 
module temperature 
above -40°C and cycle key 
switch. 

13

Inverter 2
Under 
Temperature 

Blocking 

All 

Operation in low temp environment. 

Inverter 2 power 
module temperature 
below -40°C. 

Bring inverter 2 power 
module temperature 
above -40°C and cycle key 
switch. 

14

Inverter 1
Current Sensor 
Fault 

Blocking All 

• Leakage 

current due to motor 1 stator 

short-circuit. 

• Controller’s sensor faulty. 

Current sensor of 
inverter 1 has an invalid 
offset reading at key on. 

Cycle key switch. 

15

Inverter 2
Current Sensor 
Fault 

Blocking All 

• Leakage 

current due to motor 2 stator 

short. 

• Controller’s sensor faulty. 

Current sensors of 
inverter 2 have an 
invalid offset reading at 
key on. 

Cycle key switch. 

16

- - 

All 

17

Inverter 1
Temp Sensor 
Fault 

Stopping 

All 

Inverter 1 internal temperature sensor 
not connected or shorted. 

Difference between 
inverter 1 and 
microprocessor temp 
greater than 70 °C. 

Cycle key switch. 

18

Inverter 2
Temp Sensor 
Fault 

Stopping 

All 

Inverter 2 internal temperature sensor 
not connected or shorted. 

Difference between 
inverter 2 and 
microprocessor temp 
greater than 70 °C. 

Cycle key switch. 

19

Motor 1
Over 
Temperature 

Stopping 

All 

• Motor 1 temperature is too high. 
• Wrong Motor 1 thermal probe type or 

input. 

• Motor 1 thermal probe not connected 

or shorted input. 

Motor 1 temperature is 
above the motor over 
temperature parameter 
setting. 

Bring motor 1 
temperature below over 
temperature limit and 
cycle the key switch. 

20

Motor 2
Over 
Temperature 

Stopping 

All 

• Motor 2 temperature is too high. 
• Wrong Motor 2 thermal probe type or 

input. 

• Motor 2 thermal probe not connected 

or shorted input. 

Motor 2 temperature is 
above the motor over 
temperature parameter 
setting. 

Bring motor 2 
temperature below over 
temperature limit and 
cycle the key switch. 

21

Motor 1
High 
Temperature 

Limiting 

All 

• Motor 1 temperature is too high. 
• Wrong Motor 1 thermal probe type or 

input. 

• Motor 1 thermal probe not connected 

or shorted input. 

Motor 1 temperature is 
above the motor start 
cutback temperature 
parameter setting. 

Bring motor 1 
temperature below start 
cutback temperature and 
cycle the key switch. 

Code

Fault

Level

Family

Possible Causes

 Set Condition

Clear Condition

Summary of Contents for W11E









































































Reviews: