EuroTel ETL0480TBD Technical Manual Download Page 27

Page: 27 / 37

EUROTEL - ITALY

ETL0480TBD

WARNING LED also turns off when this memory is cleared.

Shows the previous warning condition.

Shows the next warning condition.

View Work Timer

Shows the working time of the amplifier in hours

TX enable config

Extern Enabled

Amplifier externally enabled. An external signal coming from the Exciter is needed for turn-on.

Always Enabled

Amplifier always enabled. The Amplifier switches on as soon as A.C. power is switched on and the

automatic EEPROM test has been carried out by the internal microprocessor.

ALC ref. power

Changes the reference power of the A.L.C. loop and is used to set the RF power output.

Store

Stores the new reference power level.

Decreases the reference power level.

Increases the reference power level.

TX A.L.C. config

Enables o disables the A.L.C. loop. When the loop is disabled, the display shows: “A.L.C. contr. off”.

ALC Disabled

The A.L.C. control loop is disabled.

ALC Enabled

The A.L.C. control loop is enabled.

ALC on AUX input

The A.L.C. control loop is enabled, the reference power is referred to the power read on external

aux. Input.

Store LCD View

The measures on the two rows of the display now, will be displayed at power on of the amplifier.

Second level menu

DESCRIPTION

Vision Frequency

Set approximately the frequency of the Vision carrier at witch the amplifier is working, in order to

provide course correction of the frequency amplitude response of the directional couplers.

Store

Set the new working Vision Frequency.

Decreases the working Vision Frequency.

Increases the working Vision Frequency.

Page 26 CMAN0480ENG

October

2002

Summary of Contents for ETL0480TBD






































Search results

Summary of Contents for ETL0480TBD

Reviews:

Brands by name

Popular brands

EuroTel ETL0480TBD, Technical Manual

Search results

Summary of Contents for ETL0480TBD

Reviews:

Brands by name

Popular brands