background image

EUROSTER 11K CONTROLLER USER MANUAL

4

c) Connect additional heat source controller:

unplug additional heat source controller from its power supply

link  E11K controller box with alternative heat source controller box using at least 2 x
0.75 mm

2

 braided cord

connect a cable to the 

AUX 

output

 COM 

and 

NC

 or 

NO

 terminals of the E11K controller

(depending on the type of the alternative heat source) 

connect the cable to the alternative heat source controller. 

d) Connect room thermostat:

the controller may cooperate exclusively with room thermostats equipped with voltage-
free normally open (NO) output contacts 

link E11K controller box with room thermostat box (or its receiver in case of a wireless
remote control) using at least 2 x 0.75 mm

2

 braided cord

connect a cable to the 

RT

 terminals of the E11K controller

connect the cable to the 

COM

 and 

NO

 thermostat terminals. 

e) Connect pumps/throttle actuator:

connect blue wire to the 

N

 terminal

connect brown wire to the 

L

 terminal

pumps must be hooked up to the 

P1-P3

 controller terminals, respectively

throttle actuator must be hooked up to the 

throttle 

output

 N

 and 

L-open

 or 

L-close 

controller terminals (depending on the type of the throttle)

ATTENTION The controller may cooperate exclusively with a bi-state
throttle   actuated   by   a   230   VAC   actuator.   In   absence   of   power   the

throttle should close automatically.

connect protective wires of the pumps and of the throttle with the PE power cord wire.

ATTENTION Controller is a 2

nd

  insulation class device, so it needs no

grounding.   However,   every   cooperating   device   that   needs   to   be

grounded must be obligatorily connected to the protective wire.

f) Hook up power supply cable:

connect neutral (blue) wire to the 

N

 terminal 

connect live (brown) wire to the 

L

 terminal.

g) Verify the connections:

check up all cable connections and tighten the terminal box lids.

h) Mount the controller:

carefully put the controller board into its box, fix the box, and put the front cover on.

4. OPERATION
a) Turning the controller on/off

Press the  

  button  to  turn the  controller on. Firmware  version  number  is displayed,   the

ANTY-STOP

 function is executed for 30 s, then the device resumes normal operation. 

Press and hold the 

 button for 2 seconds to turn the controller off. Device screen turns blank

(only the  

light remains lit) and the throttle closes so that the fireplace goes out. Control

algorithms   will   continue   to   run   in   order   to   fully   utilize   the   produced   heat   and   to   provide
fireplace safety.

The  controller  turns  off  automatically   if the  water   jacket temperature  exceeds  the  put-out
temperature. The function is active if the  

On

  installer parameter has been set to 1. If the

parameter has been set to 0, the controller will not turn off until the temperature exceeds the

Summary of Contents for 11K












Reviews: