Euromate 107439, Original Instructions Manual

Page: 15 / 28

GB
15
You can set different open time, closed time and tem-
perature within whole week.
Window Open Function
– Open the appliance as working conditions, (fan,
warm, hot are all ok). This function only through
by Remote control.
– Press [Auto] button, the [AUTO] light is on. The
appliance is working as smart saving energy
models. (In this function, the appliance is check
and record environment temperature in immedi-
ately. It will stop working, when the appliance
check the environment are drop
≥
3 °C. The user
should restart the appliance with [ ] button)
– Press [Auto] button again, the [AUTO] light is
off. Window Open Function is closed.
Delay Function
This function can be use should be fit two points:
• the appliance is in the standby state.
• before the appliance working.
This function only through by Remote control.
– Press [Lock] button light on LED display, then
press [delay] button one time, the [Delay] light
and [I/W] light are on. press [–+] two buttons set
the Hours from 01–24 (01 = 1 o’clock, 24 = 24
o’clock… 00 = Closed etc.)
• This is open time
– Press
[Delay]
button again, the
[Delay]
light
and [II/H] light are on. Press [–+] two buttons set
the Hours from 01–24 (01 = 1 o’clock, 24 = 24
o’clock… 00 = Closed etc.)
•
This is close time
Child-Lock Function
This function only through by Remote control. When
appliance are plug in, this function can be used in any
models.
– Press [Lock] button one time, all lights and LED
display are closed, only [Power] light on. In this
condition, both control panel and remote control
are fault use.
– Press [Lock] button again, all lights are on and
both control panel and remote control are use to
succeed.
Overheat Protection
This wall mounted heater is protected with an over-
heat protection that switches off the appliance auto-
matically in case of overheating. For example: due to
the total or partial obstruction of the vents. In this
case, unplug the appliance, wait about 30 seconds
for it to cool and remove the object which is obstruct-
ing the vents. Then switch it back on as described
above. The appliance should now operate normally. If
the problem persist, please contact Customer Ser-
vice for assistance.
Cleaning and maintenance
Cleaning the unit
– Switch the unit off and allow it to cool down com-
pletely.
– Unplug from the power source.
– Wipe the unit with a damp cloth.
Changing the remote control batteries
– Open the battery compartment lid.
– Replace the batteries.
Pay attention to correct
polarity.
– Close the battery compartment lid again.
Troubleshooting
What to do when something doesn’t work…
Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the ven-
dor. You will save yourself a lot of trouble and possi-
bly money too.
If you can’t fix the fault yourself, contact your nearest
vendor. Please be aware that any improper repairs
will also invalidate the warranty and additional costs
may be incurred. Disposal
Disposal of the appliance
A crossed-out wheelie bin icon means: Bat-
teries and rechargeable batteries, electrical
or electronic devices must not be disposed of
with household waste. They may contain
substances that are harmful to the environ-
ment and human health.
Note: Press [Delay] button, screen shows
number will twinkle 5 seconds, you should
operate in time, otherwise appliance will get
back to standby. (This function is one-time
and must be reset after the power is cut off.)
DANGER! Exercise caution – risk of
injury!
Always pull the power plug before
conducting any work on the unit.
DANGER! Exercise caution – risk of
injury!
Unprofessional repairs may mean
that your unit will no longer operate safely.
This endangers you and your environment.
Error/Fault Cause Remedy
Unit does not function or does not
heat Unit is switched off or set to ventila-
tion without heating? Switch the unit on or set the required
heating level.
No power supply? Check the cable, plug, and the fuse.
Remote control doesn’t work Batteries in the remote are empty?
►
Changing the remote control bat-
teries – p. 15 .
The unit is not in standby mode? Connect the power cable to a sock-
et.