•
Fitting:
Die cast aluminium with clear tempered glass lens.
•
Class:
Class1. Requires earth connection.
•
IP Rating:
IP 65
•
Voltage:
220V - 240V ~ 50Hz
•
Dimensions:
FS255 - (H)129mm x (W)85.6mm x (D)32.4mm
FS256 - (H)176.6mm x (W)116mm x (D)38.6mm
•
Weight:
FS255 - 0.296kg
FS256 - 0.578kg
•
Lamp Type:
FS255 - 1 x 10W Integrated LED 230V
FS256 - 1 x 20W Integrated LED 230V
•
Maximum
Projected Area:
FS255 - 0.0056m
2
FS256 - 0.00966m
2
• Commercial / domestic use
• Suitable for outdoor use when used correctly.
• This fixture must be mounted in the horizontal position.
• The light source of this luminaire is not replaceable. When the light source reaches its end of life the
whole luminaire should be replaced, or the light source should only be replaced by the manufacturer.
SPECIFICATIONS
CLEANING
Sensor Controls
• Before cleaning always ensure the power supply is turned off.
• Do not immerse the luminaire in water.
• No abrasive products, solvents, detergent may be used to clean this luminaire.
• Ensure that the luminaire does not come in contact with corrosive chemicals, etc.
• Coastal areas ensure that the luminaire is cleaned fortnightly.
• TIME: the length of time the unit remains switched on after activation can be adjusted from approx.
10±3seconds to 8±2minutes.
• LUX: turning control to “Sun” symbol means the fitting is set to work day and night. Turning control to
“Moon” symbol means the fitting only works at night.
• SENS: the Maximum distance the PIR sensor detects motion (maximum is 10m).
FS255 / FS256 - attachments:
If the external flexible cable or cord of this luminaire is damaged, it should be exclusively replaced by
the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
To ensure that you get maximum longevity and maximum use out of your luminaire, please
observe the following safety instructions.
Electrical products can cause death, injury, or damage to property. Installation of the luminaire must
be carried out by a qualified electrician, in accordance with SANS 10142. On completion of
installation, ensure that the Certificate of Compliance is updated.
• Before connecting this luminaire, ensure that voltage indicated on the rating label corresponds with the
mains voltage in your home.
• When changing the lamp, ensure that the power is turned off.
• This luminaire is checked in full for conformity to the quality standards and safety requirements.
• The manufacturer / supplier is not responsible for any damage of properties and persons, caused by
the incorrect use or installation of the luminaire.
• Should you be unsure of how to install this luminaire correctly, please consult a professional electrician
or your supplier for assistance.
• Ensure all items/ components, threads and screws are tightly secured.
IMPORTANT:
• Tampering with this luminaire, IE. Using silicon sealers or incorrect cabling, will invalidate
your warranty.
• When the protection glass is damaged, it should be replaced immediately. The luminaire
must not be used without the protection glass.
• Please check whether the connection of the power cord is safe and reliable before installation.
• Always ensure that the mains supply voltage is correct.
• Always replace the lamp with one of an identical rating.
• Ensure that you do not place the luminaire near any combustible materials and / or surfaces.
• Choking hazard: May contain small parts. Keep away from children.
• Do not insert your fingers or any part of your body into the electrical contact and sockets of this product
whilst it is connected to the electricity supply.
• Item may vary slightly from the picture on the carton.
• Coastal humidity may effect the longevity of the luminaire.
• Outdoor luminaires must be cleaned to prevent rust occurring.
• Use a copper grease on all screws or strings.
IMPORTANT SAFEGUARDS
