background image

GEH-5930

INSTRUCTIONS

Criterion

TM

 Large Horizontal

Area Fixture 750-1000 Watt

READ THOROUGHLY BEFORE INSTALLING

GENERAL

This luminaire is designed for outdoor lighting

applications, and should not be used in areas of limited
ventilation, or in high ambient temperature enclosures. 
For optimum performance, it should be installed and
maintained according to the following recommendations.

UNPACKING

This luminaire has been properly packed so that no parts

should have been damaged during transit. Inspect to
confirm.

INSTALLATION

This luminaire has been configured specifically to

mount to a round or square pole.  To facilitate mounting,
open the door by releasing the two latches and swinging the
door open.  The reflector may be removed by rotating the
two fasteners 90 degrees and remove the reflector from the
luminaire.  Disconnect the socket leads to free reflector
from the luminaire. SnapDrive™ may be removed for ease
of installation.  To remove, invert luminaire, unscrew and
discard shipping screw (if so equipped), disconnect the
wire harness, then depress the spring clips downward,
rotate SnapDrive upward and lift off of the hinges
(see Figure 1).

A. MOUNTING

WARNING

Risk of electric shock

Turn power off before servicing

see instructions

WARNING

Risk of fire

Use supply wire specified on

    nameplate

CAUTION

Unit will fall if not installed properly

Follow installation instructions

For mounting to pre-drilled poles see Figure 2 for round

poles and Figure 3 for square poles.  To mount luminaire to
pole:

1. Install nut plate inside the pole.  Nut plate can be secured

inside pole with screw provided.

2. Install two (2) studs, ensuring full penetration into nut

plate.

SnapDrive Hinge

SnapDrive
Spring Clip

Figure 1

g

GE
Lighting Solutions

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or
maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be referred
to GE Lighting Solutions.

Summary of Contents for Criterion








Reviews: