Eurolinx I-HOOD, Installation, Operating And Maintenance Instructions

Page: 4 / 8

Adjustable and delayed self-switching off
With the hood in function, choose the desired speed, then
hold until it flashes the speed button that corresponds to the
minutes of sleep to be set, bearing in mind that:
corresponds to 5 minutes
corresponds to 10 minutes
corresponds to 15 minutes
During the self-switching off time, it is possible to change or
the speed set. If you choose the maximum speed, after 5 min
automatically it switches to the 3rd speed and self-switching time
will be set at that speed.
key: BT connection. Press three seconds to activate the BT
connection (the button starts flashing). Enable the BT connection
on the external device and research the hood (initials RN52-
.......). Once connected the button light stops blinking and stays
on, the display will show “BT”. Use the external device to manage
music and phone calls.
Use the key
(volume) to adjust the volume, the display will
show the volume level
To accept or end a call press the
key. During a phone call, the
display will show “CALL”. During a phone call you can adjust the
volume using the key
and .
To disconnect the external device, hold for three seconds the
key, the device will be disconnected and the backlight intensity of
the button will reduce in stand-by mode.
The feature
call and transfer music tracks has priority over
the radio
key: Radio. Press three seconds to activate the radio. The
backlight button lights up, the display will show the radio station
frequency. To change frequency press the keys
and .
After 10 seconds of non-use of the buttons, the display positions
volume.
Use the key to adjust the volume, the display will show the
volume level and .
To change frequency press the key and than the keys
and .
To turn off the radio press the radio key for three seconds,
the radio turns off and the backlight intensity of the button will
reduce in stand-by mode.
The radio does not work when the hood is already connected
with BT connection and is receiving music from the external
device or when there is an active phone call.
Phone calls and the transmission of music tracks has priority
over the radio.
In any case, after 10 seconds of unused, the display will show
the volume level.
Filters maintenance reminder
Aluminium anti-grease filters
Once the hood is switched off, after 30 hour functioning, all
the LEDs of the speed buttons switch on with a fixed light for
30 seconds to remind that aluminum anti-grease filters need
cleaning. To set the timer to zero keep the button
pressed
with the aspirator switched off until the LEDs turn off, otherwise
the timer will remain set on 30 hour functioning and the reminder
will occur again when the hood is switched off again.
Charcoal filter (for filtering hoods)
Once the hood is switched off, after 120 hour functioning, all
LEDs blink for 30 seconds to remind that the charcoal filter need
cleaning. To set the timer to zero keep the button
pressed
with the aspirator switched off until the LEDs turn off, otherwise
the timer will remain set on 120 hour functioning and the reminder
will occur again when the hood is switched off again.
4 MAINTENANCE AND REMINDERS
Always disconnect the hood from the mains before carrying out
any maintenance or cleaning operation.
Particular attention should be paid to the metallic anti-grease
filters that are designed to trap particles of fat contained in the
fumes. The metallic anti-grease filters must be washed at least
once a month with detergent in hot water (or in the dish-washer).
The filters may disc olor after a few washes. This is
normal and does not mean they have to be replaced. To remove
the metallic anti-grease filters open the bottom panel of the hood
and then remove the filter by the handle.
ATTENTION: the grease collected in the filters can easily catch
fire and it is therefore extremely important to clean the metallic
filters on a regular basis as per instructions.
The charcoal filters, if present, are designed to collect unpleasant
odours in the cooking fumes. The air is then released
purified in the environment. The charcoal filters must not be
washed, but replaced 2 or 3 times a year, depending on how
much the hood is used. New filters are to be requested directly
to the manufacturer.
To replace the charcoal filters, just remove the motor protection
panel, centrally positioned between the metal filters: locking is
performed with magnetic closures; simply exert a modest manual
force, without the use of tools. At this point you can remove the
charcoal filter through a rotation of about 90° respect to their
position to unhook them from the locking lugs, accompanying
then the filter downward, without the aid of tools. Fig. 3.
To reinstall the new carbon filters, reverse the operations.
In order to remove the remaining glue or any impurity, the cooker
hood must be cleaned immediately after installation and after
having removed the protective film.
The cooker hood must be cleaned frequently both internally and
externally (at least once a month).
Do not let dirt gather on the inner and outer surfaces of the hood.
To clean the exterior of the hood do not use either acid or basic
products, or abrasive sponges.
Clean the hood with a sponge dampen in warm water and
a little quantity of neutral detergent (for example dishwasher
detergent), in order to remove possible particles of grease.
Rinse with a damp cloth, removing all the detergent carefully,
following the satin finish direction on the steel surface.
Drying is very important, especially in areas where water is
particularly hard and leaves limestone.
The hood features a LED light that, in addition to offering a
good lighting and a significant energy savings, are guaranteed
to last on average 10 times more than traditional lights. For
replacement, contact the Assistance Service.
All the ordinary and extraordinary maintenance can be
performed without having to remove the hood.
5 WARNINGS
The present instruction manual is an integral part of the appliance
itself, therefore it must be carefully kept and ALWAYS accompany
it, even in case of its assignment to another owner or user or in
case the cooker hood is moved to another installation plant. Make
sure that the voltage (V) and frequency (Hz) indicated on the
data plate inside the unit match those available at the installation
site. Any eventual adjustment to the electrical system, which may
be necessary to install the cooker hood, must be carried out
only by competent people.
Any repair carried out by no competent people may cause