OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS cont.
Cleaning & Changing the
HEPA Dust Cup Filter
Warning:
Always unplug the unit from
electrical outlet before opening the Dust
Cup (container).
Important:
Do
NOT
use the HEPA filter
cartridge without the debris screen in
place.
Warning
:
After each Use - Always
remove the Filter Debris Screen from the
HEPA Dust Cup Filter, then vigorously
“
TapClean
” HEPA Filter until no more
dust can be removed.
IMPORTANT, Please Note :
The
“TapClean” HEPA Dust Cup Filter &
Debris Screen will stop most of the tiniest
dust particles and airborne allergens from
re-entering the air you breathe. In fact it
stops 99.97% of all particles as small as
0.3 microns - many times smaller than a
human hair!!! Because of this incredible
filtration performance, the HEPA Dust Cup
Filter will quickly accumulate, inside the
white filter folds, many fine dust particles
that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. This can
cause the motor to overheat and the re-
settable thermostat to trip. (Should this
happen turn off the switch, unplug the unit
and allow unit to cool down. Clean the
HEPA Filter and Debris Screen as
described in this section, then reconnect
unit and proceed with vacuuming.)
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, dust cup filter,changing the filters or
performing maintenance/trouble shooting
checks.
4.
Attaching Extension Tubes to
Floor Attachment
Push extension
tube into the floor
attachment.
Extension
Tube
1.
Attaching the Flexible Hose
into the Vacuum
Connect the flexible hose into the air
intake duct. Push in until you hear a
“click”, indicating it is in its position.
To remove the flexible hose, reverse
the operation.
2.
Fitting the Chrome
Telescopic Tube to the
Curved Wand / Hose
Extension
Push the chrome telescopic tube
into the curved wand / hose
extension, as shown in the
illustration.
Variable Suction Control
Your vacuum cleaner includes an manual
variable suction control on the hose
extension. The suction power can be
adjusted by moving the slide regulator to
the desired position. For example. Less
suction is required on upholstery and
draperies compared to thick shag
carpets, which require maximum suction.
1.
Crevice Tool
For radiators, crevices,
corners, baseboards and
between cushions.
2.
Dusting Brush
The dusting brush is used for
the furniture, venetian blinds,
books, lamp shades and
shelves.
3.
Extending the Chrome
Telescopic Tube
Push forward the plastic knob
and pull the smaller tube
outward.
5.
Air Driven Turbo Brush
The efficiency of your Air Driven
Turbo Brush depends on the bristle
brush rotating at high speed. Strong
air suction is needed to accomplish
this. In order to endure that
maximum air suction is maintained,
please read the following instructions:
•
Empty the Dust Cup frequently during
use.
•
Always “
TapClean
” the HEPA dust
cup filter and debris screen each time
the dust cup is emptied.
•
Ensure that the rotating bristle brush
is kept free of hair and string.
•
Inspect the turbine regularly to ensure
that the air passage is free of dirt and
debris.
Floor to
Carpet Nozzle
Assembling Your Vacuum Cleaner
Note:
Always remove the power plug
from the wall outlet before assembling or
removing accessories.
Note:
Before using the appliance,
unwind a sufficient length of cable and
Insert the plug into the wall socket. A
yellow mark on the power cord shows the
ideal cable length. Don’t pull the power
cord beyond the red mark.
Power Cord
Your vacuum cleaner includes a power
cord, which is automatically retractable.
To extend your power cord, pull from
rear and extend to desired length.
When cleaning is finished, first switch
off power and disconnect plug from
electrical outlet. Then press on cord
rewind button. If the cord does not fully
retract, pull it out again and then press
on cord rewind button.
1. Insert the power plug into the wall
outlet.
2. Press the Power On/Off Switch to
activate the vacuum cleaner.
3. To rewind the power cord,
press the cable rewind button
with one hand and guide the
power
cord with the other hand
to ensure that it does not whip
causing damage.
1. Push the Power On/Off switch
to the OFF position to
disconnect the power.
2. Remove the flexible hose (see
page 3).
3. Push the dust cup lock and
open the dust cup.
Crevice Tool and Dusting Brush
Plastic Knob
3
4
