Euresys 1633-LH Hardware Manual Download Page 67

Page: 67 / 210

Board Status LED

Board status LED indicator states

LED
state

Symbol

Meaning

Off

No power.

The board is not powered or the power distribution network is not
functional.

FPGA NOK.

The FPGA start-up procedure is not completed.

The normal

completion time is around 100 milliseconds.

Solid
green

Board status OK.

The main power distribution network is operational and the FPGA
start-up procedure has successfully completed.

Solid
red

Board status NOK.

Possible causes are:

●

There is no power delivered on the +12 V rail of the PCI Express
connector slot

●

At least one power converter of the main power distribution
network is unable to operate properly.

This might be caused by

excessive temperature due to inadequate board cooling,
accidental short-circuits having blown one (or more) protection
fuses, inappropriate supply voltages, etc.

eGrabber

Hardware Manual

Summary of Contents for 1633-LH



















































































































































































































Search results

Summary of Contents for 1633-LH

Reviews:

Related manuals for 1633-LH

Brands by name

Popular brands

Euresys 1633-LH, Hardware Manual

Search results

Summary of Contents for 1633-LH

Reviews:

Related manuals for 1633-LH

Brands by name

Popular brands