manualshive.com logo in svg

Euphonix S5 Surface Modules, Manual, Page: 49 / 50

Share
Download
Euphonix S5 Surface Modules Manual Download Page 49

 

 

 

S5 Control Surface/Frame Manual 

Page 49 

Version 1.0   ©1999 Euphonix, Inc. 

 

Parts List (cont)

 

 

System 5 Frame Set, 9ft:  Part# 946-06840-01 

Item#

 

Item Description

 

Qty 

726-06437-01

 

Beam-Box 9ft S5

 

2 

726-06400-01

 

Clamp-Beam

 

4 

726-06439-01

 

Beam-Back 9ft S5

 

1 

726-06402-01

 

Plate-Back Beam

 

2 

726-07168-01

 

Palm Rest-9ft S5

 

1 

726-06404-01

 

Plate-Palm Beam

 

2 

726-06411-01

 

Brace-Back

 

2 

726-06686-01

 

Cover-Back 3ft

 

3 

600-07223-00

 

Power Strip-Iec320-Reworked

 

2 

032-07147-00

 

Iec320 Jumper Cordset-0.5m

 

5 

032-07148-00

 

Iec320 Jumper Cordset-1.0m

 

3 

032-07149-00

 

Iec320 Jumper Cordset-1.5m

 

2 

032-07150-00

 

Iec320 Jumper Cordset-2.5m

 

1 

030-07180-01

 

Ca-Internal Ethernet/9ft  

1 

936-07218-01

 

S5 Frame Bolt Kit

 

1 

043-06688-00 

5/16-18x3.5 Bolt Hex-Head-Zi 

16 

082-06689-00 5/16 

Lockwasher 

16 

046-06401-00 

5/16-18x2.25 Bolt Flat/Soc/Ss 

8 

046-06421-00 3/8-16x1.25l 

Buttonhd/Skt/Ss 

8 

081-07193-00 3/8 

Flat/Wash/Ss 

8 

936-07241-01

 

S5 Rear Panel Bolt Kit 

1 

044-07236-00 ¼-20x3/8 

B4cs 

20 

936-07239-01

 

S5 Tee Hardware Kit

 

1 

000-06690-00 

5/16-18x.375 Tee Nut/Cz 

22 

044-06686-00 

5/16-18x.375 Bolt Socket Hd/Cz 

22 

936-07240-01

 

S5 Thumb Screw Kit

 

10 

040-06833-00 

10-32x3/8 Thumb\Washer Face 

4 

 

Summary of Contents for S5 Surface Modules



















































Reviews:

No comments