EUCHNER CES-A-5 Series Operating Instructions Manual Download Page 13 | Manualshive

Page: 13 / 32

EUCHNER CES-A-5 Series Operating Instructions Manual Download Page 13

13

2110182-09-12/18 (Translation of the original operating instructions)

Operating Instructions

Non-Contact Safety Switch CES-A-C5H-EX

EN

Note the following points:

Ì

Actuator and safety switch must be easily accessible for inspection and replacement.

Ì

Actuator and safety switch must be fitted so that

-the front faces are at the minimum switch-on distance 0.8 x S

ao

or closer when the guard is closed. To avoid entering

the area of possible side lobes, a minimum distance is to be maintained in case of a side approach direction. See

chapter 13. Technical data, section Typical operating distance for the related actuator.

-when the guard is open up to the distance S

ar

(assured switch-off distance), a hazard is excluded.

-the actuator is positively mounted on the guard, e.g. by using the safety screws included.

-they cannot be removed or tampered with using simple means.

Ì

Pay attention to the maximum tightening torque for the read head or safety switch and actuator fastenings of 1 Nm. For

read heads/actuators made of PE-HD, the maximum tightening torque is only 0.5 Nm.

«
...
11
12
13
14
15
...
»

Summary of Contents for CES-A-5 Series

































Reviews:

No comments