EUCHNER BR-FLX, Operating Instructions Manual

Page: 34 / 40

Operating Instructions
Transponder-Coded Safety Switch CTM-C2-BP/BR-FLX
34
(translation of the original operating instructions) MAN20001574-01-09/22
16. Technical data
NOTICE
If a data sheet is available for the product, the information on the data sheet applies.
16.1. Technical data for safety switch CTM-C2-BP/BR
Parameter
Value
Unit
min. typ. max.
General
Material
- Seals
Fluorinated rubber (FKM)
- Switch housing Reinforced thermoplastic
Installation orientation Any
Degree of protection
IP65/IP67/IP69/IP69K 1)
(screwed tight with the related mating connector)
Safety class acc. to EN IEC 61140 III
Degree of contamination (external, acc. to EN 60947-1) 3 (industrial)
Mechanical life 1 x 10
6
operating cycles
Ambient temperature at U
B
= 24 V -20 - +60 °C
Actuator approach speed - - 20 m/min
Actuating/extraction force Device dependent, see www.euchner.com N
Locking force F
max
1300 N
Locking force F
Zh
F
Zh
= F
max
/1.3 = 1000 N
Weight Approx. 0.16 kg
Connection (depending on version) 1 plug connector M12, 8-pin
Operating voltage U
B
(reverse polarity protected, regulated,
residual ripple < 5%)
24 ± 15% (PELV) V DC
Current consumption I
UB
at U
B
= 24 V - 385 500 mA
The following applies to the approval acc. to UL Operation only with UL Class 2 power supply or equivalent measures
Switching load acc. to UL 24 V DC, Class 2
External fuse (operating voltage U
B
) 0.7 - 8 A
External fuse (guard locking solenoid control input U
IMP
) 0.1 - 2 A
Rated insulation voltage U
i
50 V
Rated impulse withstand voltage U
imp
0.5 kV
Rated conditional short-circuit current 100 A
Shock and vibration resistance Acc. to EN 60947-5-3
EMC protection requirements Acc. to EN 60947-5-3
Ready delay - 5.5 - s
Risk time for single device - - 200 ms
Risk time extension per device 10 ms
Turn-on time
ms - Guard lock monitoring inactive - - 100
- Guard lock monitoring active - - 500
Discrepancy time between both safety outputs acc. to
EN 60947-5-3
- - 10 ms
Test pulse duration - - 0.3 ms
Test pulse interval - - Approx. 100 ms
Safety outputs FO1A/FO1B
Semiconductor outputs, p-switching, short circuit-proof
Output voltage U
FO1A
/U
FO1B
2)
V DC - HIGH U
FO1A
/U
FO1B
UB - 1.5 - UB
- LOW U
FO1A
/U
FO1B
0 - 1
Switching current per safety output 1 - 150 mA
Utilization category acc. to EN 60947-5-2 DC-13 24 V 150 mA
Caution: outputs must be protected with a free-wheeling diode in case of inductive loads
Switching frequency - - 0.5 Hz
Monitoring outputs Ox/C p-switching, short circuit-proof
Output voltage 0.8 x UB - UB V DC
Max. load 1 - 50 mA
Solenoid IMP (control input of guard locking solenoid)
Input voltage
V DC - Guard locking not active (open) 0 - 5
- Guard locking active (closed) 20.4 - 26.4
Solenoid current consumption I
IMP
mA
- Guard locking active (closed) 20 - 50
Connection rating at max. switching frequency 3 W
Duty cycle 100 %