manualshive.com logo in svg

EUCHNER 099265, Manual, Page: 26 / 38

Share
Download
EUCHNER 099265 Manual Download Page 26

Manual EKS Ethernet TCP/IP 

Page 26/38 

Subject to technical modifications 

2547185-01-10/22 

7  Setup 

Perform setup in the following sequence: 
1.  Set the DIP switches of the device  

(see chapter 4.7). 

2.  Check whether mounting and electrical connection are correct 

(see chapter 5 and chapter 6). 

3.  After the power supply is plugged in, the LED on the front of the compact Electronic-Key adapter is 

illuminated, or the CF LED on the interface adapter are initially illuminated red. After the EKS has booted 

and a network cable has been connected, the LED on the front of the compact Electronic-Key adapter is 

illuminated, or the ON LED on the interface adapter is illuminated green and signals readiness for operation. 

4.  Place the Electronic-Key in the Electronic-Key adapter. The LED on the front of the compact Electronic-Key 

adapter or the ACTIVE LED on the interface adapter changes to yellow. 

5.  Important: for the version EKS 

FSA

, all safety functions must also be thoroughly tested. 

7.1  Network settings 

You need the following information to integrate the device into the network: 

  IP address of the host computer with which you want to configure the device. 

  Free IP address that can be assigned to the device (not needed if the IP address is obtained automatically 

from a DHCP server) 

  Subnet mask of the network in which the device is to be operated 

  If necessary, information on valid gateway 

  If necessary, information on valid DNS server 

 

Information! 

The TCP connection to the device must be made using port 2444. If the Ethernet ActiveX

®

 module is 

used, this port is set by default. If the connection is to be made from a control system, for example, this 

port must be set explicitly.

 

7.1.1  Network settings for a configuration PC with Windows

®

 

 

Information! 

 It is assumed that you connect the PC to the EKS read/write station as shown in the following 

example. 

 For connection, you need a (Cat 5) patch cable.  

 You must first modify the network settings on the PC so that the web interface can be opened.  

 Enter IP address for the PC from 192.168.1.2 to 192.168.1.254. 

 Enter subnet mask for the PC as 255.255.255.0  

 

Figure 4: Connection of configuration PC 

 

 

Windows

®

 

Summary of Contents for 099265







































Reviews:

No comments