Eubank TV36D, Installation, Operation And Maintenance Manual

Page: 2 / 18

REV
G 3/01/17
2 309001
6
.
Your equipment is covered by a LIMITED WARRANTY against
defects in material and workmanship.
This is a vertical, wallmount unit designed for many different
applications in both residential and commercial settings. It is self-
contained and arrives completely assembled, factory-charged and
wired. The unit is 100% run-tested at the factory to ensure proper
operation. Your unit is supplied with high-quality copper tubing and
enhanced aluminum-finned coils for high heat transfer efficiency
and long life. The unit cabinet is constructed of G-90 galvanized
steel. All exterior surfaces are finished with a baked-on polyester
coating. This will provide excellent corrosion protection in most
applications. However, if the unit is installed in an area with a
corrosive atmosphere, such as near an industrial plant or on the
seacoast, additional coating should be considered to extend the
life of the coils and cabinet.
This unit was designed for up to 105ºF of ambient temperature.
INSPECTION AND UNPACKING
A thorough inspection of the shipping container should be made
immediately upon receiving your unit. Look for any punctures or
openings. If it appears as if damage has occurred, it should be
noted on the freight bill before signing. The delivering carrier
should be contacted immediately to inspect damage, and no
installation work should begin until this inspection is completed.
DANGER:
BEFORE PERFORMING ANY
WORK ON THIS EQUIPMENT, POWER SUPPLY
MUST BE TURNED OFF AT THE HOUSEHOLD
SERVICE BOX TO AVOID THE POSSIBILITY OF
SHOCK, INJURY, DEATH, OR DAMAGE TO EQUIPMENT.
SAFETY RULES
WARNING:
FAILURE TO FOLLOW THESE
RULES AND INSTRUCTIONS COULD CAUSE A
MALFUNCION
OR DESTRUCTION OF
EQUIPMENT WHICH COULD RESULT IN
PROPERTY DAMAGE, SERIOUS BODILY INJURY, OR
DEATH.
1. Installation and repair MUST be done by a qualified person.
The equipment should be inspected before use and at least
once annually by a professional service person.
2. AVOID ELECTRICAL SHOCK! Turn power OFF when
servicing. There may be more than one disconnect switch
to de-energize unit.
3.
Close cover(s) before returning breaker(s) to “ON” position.
4. Please observe good safety practices by wearing personal
protective equipment such as gloves and safety glasses to
avoid injury.
5. Installation MUST conform to local codes. In the absence of
local codes, refer to the National Electrical Code (NEC),
ANS/NFPA No. 70-1993 and recommendations made by
the National Board of Fire Underwriters.
In our continuing effort to improve our product, specifications may
change without notice. If there are any questions, please see the
contact information on the last page of this manual.
In all cases, the equipment MUST be installed in accordance with
the installation instructions described in this manual.
WARNING:
IMPROPER INSTALLATION MAY
DAMAGE EQUIPMENT, CAN CREATE A HAZARD,
AND WILL VOID THE WARRANTY
OPERATING INSTRUCTIONS
If heating and cooling functions are controlled by separate
thermostats, turn the furnace thermostat to the “OFF” position
during the cooling season to prevent simultaneous operation of the
heating and cooling systems. Reverse the procedure during the
heating season.
If the same thermostat controls both heating and cooling
functions, set the thermostat to either HEAT or COOL as desired.
Set the desired temperature on your thermostat and set the fan
switch to “ON” (for continuous air circulation) or to “AUTOMATIC”
(for air circulation only when the air conditioning system is
operating).
IMPORTANT: Wait at least three (3) minutes after turning the air
conditioner off before trying to restart. If an attempt is made to start
the compressor before the refrigerant pressures are equalized, the
compressor motor may trip on its overload. An additional waiting
period will be required before restarting.
MAINTENANCE
1. Always install and keep filters clean. Check filters every 2
weeks. Clean or replace if necessary. The factory-installed filter is
located behind the center front access panel.
TO CHANGE SYSTEM FILTER:
A. Turn the power to the unit off at the unit disconnect. The
disconnect is located on the front of the T Series unit
behind a small access door.
B. Remove the front center access door from the unit.
C. Remove and replace the filter with the type and size
indicated in the table below.
D. Replace the access door and turn on the power to the unit.
NOTE: If your system has a filter grille installed in the return air
opening, the unit filter should have been discarded during
installation.
The filter installed into the return air grille assembly should be
replaced with the same size and type provided with the grille.
If your system is equipped with a fresh air intake, the filter for the
fresh air assembly is accessed through the front center panel. The
filter is a permanent washable type.
UNIT MODEL QTY. FILTER SIZE TYPE
36 1 16 x 30 x 1 (standard) Disposable
36 1 16 x 30 x 2 (optional) Pleated
48, 60 1 20 x 30 x 1 (standard) Disposable
48, 60 1 20 x 30 x 2 (optional) Pleated
WARNING
: SERIOUS INJURY MAY RESULT IF
WATER SPRAY IS DIRECTED TOWARD LIVE
ELECTRICAL
CONNECTIONS OR POWER
SOURCES.
TO CLEAN FRESH AIR INTAKE FILTER:
A.
Follow steps A and B above.
“TO CHANGE SYSTEM FILTER”.
B. Gently pull out the filter from the bottom.
C. Wash the filter with water.
D. Reinstall the filter, by sliding it into the
retaining rail.
E. Replace the access door and turn the
power on to the unit.
2. Keep the outdoor coil clean. Wash it
down with a garden hose if necessary.