manualshive.com logo in svg

eTung MD-649 DTU, User Manual, Page: 14 / 52

Share
Download
eTung MD-649 DTU User Manual Download Page 14

 

 

                                   

MD-649 User Manual 

14 

 

 

2.

 

Device Configurations 

This chapter introduces how to use MD-649 and related parameters.             
1.

 

Configurations   

2.

 

Parameters   

3.

 

Restore to default   

4.

 

Firmware Update   

5.

 

Remote Configurations   

 

 

2.1

 

Configurations 

2.1.1

 

Preparation 

 

Serial line used to connect MD-649 with PC or user devices   

 

4G all-frequency antenna   

 

Power adapter   

 

one SIM card, either from China Unicom, China Telecom or China 
Mobile, that applies 4G and can access internet directly via NET 

2.1.2

 

Configuring MD-649 

 

Connect MD-649 with PC using 9-pin 9-hole serial line   

Attention:

 although MD-649 serial port supports RS232 and 

RS485 at the same time, when using DTU configuration software 
to configure it, whether the serial port type is RS232 or RS485, 

the configuration software communicate with MD-649 as RS232 
type. Therefore, although the serial port type is set to RS485, 

when connecting with PC to configure it, use 9-pin 9-hole serial 
line directly and RS485-RS232 converter is not needed. 

   

 
 

 

Find and run MD-649 dedicated configuration executable 
DTUcfg.exe either from the CD or by downloading from eTung 

Summary of Contents for MD-649 DTU





















































Reviews:

No comments