manualshive.com logo in svg

ETOP P/I-P3BVL, User Manual

Share
Download
ETOP P/I-P3BVL User Manual Download Page 29

Chapter 2   Installations   

P/I-P3BVL  User's Manual 23 

 

 Front Panel Connector 

The front panel of the case has a control panel which provides light 
indication of the computer activities and switches to change the 
computer status.  
 

 

     SMI  PWR        SPEAKER   KEYLOCK    IDE 
           LED  RESET                          LED 

 

Ø 

SMI/Hardware Switch 

This connector supports the "Green Switch" on the control panel, 
which, when pressed, will force the system into the 
power-saving mode immediately. 

 

 

SMI 

SMI  

Pin # 

Signal Name 

 

1 

Sleep 

 

2 

Ground 

 

Ø 

Power LED 

This connector indicate the computer power status. 

 

 

   Power 

Power LED  

Pin # 

Signal Name 

 

3 

+5V 

 

4 

Ground 

 

 

Ø 

RESET Switch 

The reset switch allows the user to reset the system without 
turning the main power switch Off and then On. Orientation is 
not required when making a connection to this header. 

 

 

      Reset 

RESET    

Pin # 

Signal Name 

 

5 

Reset 

 

6 

Ground 

 

Summary of Contents for P/I-P3BVL





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands