ETM ETM9120-1 Configuration Tool User Manual Download Page 44 | Manualshive

Page: 44 / 46

ETM ETM9120-1 Configuration Tool User Manual Download Page 44

Page 44 of 46

For Support C61-2-9956-7377

Or

[email protected]

ETM9120 9140 Configuration Tool Userguide201406RV001

First Point Set, Set Next. Send SPACE when done!

8. Set the Multifunction calibrator to 2V output, then press “SPACE” key to finish

You need to finish steps 6 through 8 within the 20 seconds timeout period. You can
increase the timeout value from 20 to 30. If the operation has timed out you will see the
following Error Message, no settings will be saved to the modem in this situation:

ERROR: Wait Timeout

9. If successful the modem will respond with OK

10. To check press “READ MEMORY”, and confirm by reviewing the A/D Calab Param

The X1 and X2 range is the number of bits that an analogue can be divided into and is from
0 to 4096. So nominally 0 = 0V on the modems input and 4096 = 2.5V on the modems input.

11. I/O3 is now scaled to -10 dgC to 50 dgC for an input of 0-10V. Readings can be checked at

various voltage input levels by setting the voltage input and sending ETRAIX, where X is
the I/O number

«
...
42
43
44
45
46
»

Summary of Contents for ETM9120-1















































Reviews:

No comments