background image

South Bend, Indiana USA 

 |

  networketi.com

FPT-130 INSTALLATION MANUAL  |  

PART NO. 

25165

 REV 

F

TABLE OF CONTENTS

FPT 130 Overview.................................................................................... 2

Installation ................................................................................................ 3

Power Source and Load Connections................................................... 4

Temperature Sensor ................................................................................ 5

External Alarm .......................................................................................... 5

Dip Switches ............................................................................................. 6 

Operation ................................................................................................. 7

6SHFLƓFDWLRQV

 ........................................................................................... 9

Pilot Duty

The FPT 130 General Purpose Thermostat with GFEP cannot be used 

for Pilot Duty applications.

Devoir du pilote

Le thermostat à usage général FPT 130 avec GFEP ne peut pas être 

utilisé pour les applications Pilot Duty

Resistive Load Usage Only

This product is not for use with Inductive loads. Inductive loads may 

create nuisance tripping of the Ground–Fault Equipment Protection 

circuit.

Utilisation de charge résistive uniquement

Ce produit n’est pas destiné à être utilisé avec des charges inductives. 

Les charges inductives peuvent créer un déclenchement intempestif 

du circuit de protection de l’équipement contre les défauts à la terre.

Abnormal Odor or Smoke

In the event of smoke or a burning or abnormal odor, immediately 

interrupt power to the unit by turning off the circuit breaker protecting 

the unit.

MODEL FPT-130

TRACON

®

SINGLE–POINT FREEZE PROTECTION HEAT–TRACE CONTROL

Heat Tracing Sales        Mt. Airy, MD        (410) 795-2223        www.heattracingsales.com

Heat Tracing Sales        Mt. Airy, MD        (410) 795-2223        www.heattracingsales.com

Summary of Contents for Tracon FPT-130












Reviews: