background image

4

1• YOUR SAFETY AND THAT OF OTHERS

• These precautions are vital to your safety.  

However, the recommendations given are not exhaustive and due 

care should always be exercised when using your mower.

• By loading and unloading of the machine it is recommanded to use 

ramps or to ask help for the loading operation.

MAINTENANCE AND STORAGE

• Always maintain the machine and accessories in perfect working 

condition.

• Replace worn or damaged parts for greater safety.
• Cleaning or servicing the mower should not be started before having 

stopped the engine and disconnected the spark plug.

• It is highly unadvisable to use a high pressure cleaner which could 

damage some of the parts.

• Always use recently purchased petrol. Old petrol could leave gum 

deposits in the carburettor, leading to leaks or make the engine 

difficult to start. Only buy unleaded petrol and store for maximum 

one month. Store the petrol in a clean container not used for other 

purposes.

• 

WARNING:

 fuel is highly flammable.

• NEVER STORE, POUR OR USE PETROL NEAR A NAKED 

FLAME or near devices such as stoves, water-heaters with pilot 

lights or any other device liable to produce sparks.

• Always fill in the fuel tank outside a building in an open space. Do 

not smoke during this operation.

• Add fuel before starting the engine.
• Never remove the fuel cap whilst the engine is running or hot. 

Allow the engine to cool for few minutes before filling.

• Ensure that the fuel tank and fuel can caps are replaced correctly.
• Do not attempt to start the engine when any petrol has been spilt, 

when you can smell petrol or when other explosive conditions 

are present. Remove the mower from the spillage area and avoid 

causing any source of ignition until the petrol vapours have 

dispersed.

• Do not carry the mower with petrol in the tank or with the feed tap 

open.

• Do not modify the regulator springs, rods or other parts to increase 

the engine speed. Operate the engine at the recommended speed. 

• Do not check the spark by removing the spark plug. Use an 

approved checking system.

• Do not pull the starter when the spark plug is out. If the engine is 

flooded, bring the gas lever to the MAXI position and pull until the 

engine starts. 

• Do not knock the engine wheel with a hammer or hard object. 

Otherwise, the wheel may break during operation. Have all major 

servicing operations performed by an authorised ETESIA repairer 

who has the appropriate tools. 

• Do not use the engine without the silencer. Check the silencer 

regularly and have it replaced if it is damaged or leaking.

• Do not touch the exhaust pipe, cylinder or fins when hot. Otherwise, 

you may get burnt.

• Do not use the mower in wooded areas, brush or on fallow or grassy 

ground if the exhaust pipe is not fitted with a spark arrester (the 

owner or user is responsible for ensuring that the spark arrester is in 

good condition).

• Do not start the engine when the air filter or air filter cover is 

removed.

• To prevent the engine from starting accidentally, remove the spark 

plug cap during servicing operations.

• Clean the cylinder fins and regulator mechanism of any dirt, grass 

residues and other materials which could alter the engine speed.

• Pull the starter cord slowly till you feel resistance. Then pull it  

energetically to prevent recoiling and hurting your hand or arm.

• Check the fuel piping and connections for cracks and leaks and 

have them changed if necessary.

• The spare blades must only be fitted on machines for which they are 

designed, in accordance with the instructions.

• The use of counterfeit parts or poor maintenance can alter the 

performance of your product, or present a danger to you and 

other people. Use only original parts and follow the maintenance 

schedule.

RESPONSIBILITY

• No responsibility will be accepted by the manufacturer in the event 

of failure to comply with this manual or with current regulations.
Do not dump your grass clippings in unauthorized areas.

• Never attempt to adjust your mower without the prior approval of 

the manufacturer.

• Any modification not authorised by ETESIA could render the machine 

dangerous and lead to serious injury during use. ETESIA shall accept 

no responsibility if these instructions are not followed.

IDENTIFICATION OF THE MOWER

• The serial number off your mower is on the identification label on 

your mower.

• Always give this number to your dealer for all servicing on your 

mower.

• You will only be ready to use this mower after you read the safety  

instructions. Read completely this manual for the using and the 

servicing of the mower.

Summary of Contents for PRO51 D

























Reviews: